Bedienungsanleitung Panasonic SC-BTT195 (Seite 43 von 52) (Englisch)

533951

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Reference

VQT3X51

Noise is excessive.

¾ Change the audio to be output as monaural.

1 Press and hold [jAUDIO].

2 Press [jAUDIO] to select “MONO”.

The sound becomes monaural.

≥ To cancel, press the button again or change

the frequency.

In normal circumstances, select “AUTO STEREO”

I can’t connect to the network.

¾ Confirm the network connection and settings.

(> 14, 15, 34)

¾ Check the operating instructions for each

device and connect accordingly.

When using wireless LAN connection, video from

the DLNA Certified media server is not played back

or video frames are dropped during playback.

¾ Higher transfer rate router such as 802.11n

(2.4 GHz) wireless router may solve the

problem. If you use 802.11n (2.4 GHz)

wireless router, it is necessary to set the

encryption type to “AES”.

Simultaneous use with a microwave, cordless

telephone etc. at 2.4 GHz may result in

connection interruptions or other problems.

On the “Wireless Settings” screen (

34), the

continuous lighting of at least 4 “Reception”

indicators is the target for a stable connection. If 3

or fewer indicators are lit or the connection is being

interrupted, change the position or angle of your

wireless router and see if the connection state

improves. If there is no improvement, connect to a

wired network and perform the “Easy Network

Setting” (

15) again.

Messages

The following messages or service numbers

appear on the television or unit’s display.

Cannot play.

¾ You inserted an incompatible disc (Discs

recorded in PAL video, etc.).

Cannot display on this unit.

¾ You tried to play a non-compatible image.

¾ Confirm “SD” on the unit’s display is not

displayed and re-insert the card.

No disc inserted.

¾ The disc may be upside down.

$ This operation is not available.

¾ Some operations are unsupported by the unit.

For example;

–BD-Video: During playback, reverse

slow-motion or reverse frame-by-frame is

not possible.

IP address is not set.

¾ The “IP Address” in “IP Address/DNS

Settings” is “---. ---. ---. ---”. Set the “IP

Address”, “Subnet Mask”, and “Default

Gateway”. (Select the automatic address

acquisition if necessary.)

The current wireless network security setting

is weak. It is recommended to change to a

stronger security setting.

Authentication type for the wireless LAN is set to

“Open system”, or the encryption type is set to

“No encryption”. It is recommended to encrypt for

safety reasons. For details, refer to the

instructions of the wireless router being used.

Encryption is required when playing back video,

etc., from DLNA compatible devices.

F99

¾ The unit fails to operate properly. Press [Í/I]

on the main unit for 3 seconds to switch the

unit to standby, then switch back on.

Network

On the television

On the unit’s display

SC-BTT190P_eng.book 43 ページ２０１２年２月２０日　月曜日　午後５時５分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-BTT195 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-BTT195

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info