Bedienungsanleitung Panasonic sc dt 310 (Seite 38 von 40) (Englisch)

370514

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

RQT6924

Reference

≥Some operations may be prohibited by the disc.

≥

The unit may not be operating properly due to lightning, static electricity or some other external factor.

Reset procedure:

Press [Í] to switch the unit to the standby mode and then back to ON.

Alternatively, press [Í] to switch the unit to the standby mode, disconnect the AC mains lead, and

then reconnect it.

≥Check the batteries are installed correctly. 9

≥The batteries are depleted: Replace them with new ones. 9

≥Point the remote control at the remote control sensor and operate.

≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.

≥This unit cannot play discs other than the ones listed in these operating instructions. 5

≥

You can only play DVD-Video if their region number is the same or includes the same region number as

the unit or if the DVD-Video is marked “ALL”. Confirm the region number for the unit on the rear panel.

≥The disc may be dirty and may require cleaning. 5

≥Ensure that the disc is installed with the label of the side to be played facing upwards. =

≥Check that the DVD-RAM has something recorded on it.

≥This function is dependent on software availability.

≥Try selecting from the disc’s menu if one is available. >

≥This function is dependent on software availability.

≥Subtitles are cleared from the television. Display the subtitles. A

≥Change the position of the subtitles with

“

Subtitle Position

”

in the GUI screen. H

≥This function is dependent on software availability.

≥This function is dependent on software availability. Even if a disc has a number of angles

recorded, these angles may be recorded for specific scenes only.

≥Select

“

DVD

”

as the source.

≥Cancel all group, program and random play. @

≥

You cannot add markers while playing a play list or if the disc’s play time doesn’t appear on the unit’s display.

≥The unit reads and displays the markers added with a DVD vido recorder. You can clear them but

reappear when you switch the unit to standby, change the source, or open the disc tray.

≥The unit numbers markers by time so they change when you add and delete them.

≥You cannot select random or program play with some DVD-Video.

≥Folders deeper than the eighth layer are displayed as the eighth layer.

≥While stopped and “DVD” is the source, press and hold [∫] on the unit and [S10/-/--] on the

remote control for about 3 seconds until “Initialized” disappears from the television. Turn the unit

off and on again.

All settings will return to the default values.

≥Reload the disc for the setting to be effective.Press [<] to open the tray, then press [1] (play) to

start play.

≥The unit may not operate properly if the disc is damaged or dirty.

Press [

] and after the display disappears, wait a few seconds, then press [

] again and eject the disc.

Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do

not solve the problem, consult your dealer for instructions.

Power

Troubleshooting guide

Operation

(Reference pages are shown as black circled numbers 9.)

≥Insert the AC mains lead securely into the household mains socket. 9

≥≥

≥The unit was switched to standby by the sleep timer.

No power.

The unit is automatically switched

to the standby mode.

Sound

No sound.

Distorted sound.

≥Check the connections. 7

≥Turn the volume up.

≥Turn muting off. N

≥Switch off the unit, determine and correct the cause, then switch the unit on.

Causes include:

–Shorting (bare wires touching) of positive and negative speaker wires.

–Using speakers with an impedance lower than that rated for this unit.

–Straining of the speakers through excessive volume or power.

–Using the unit in a hot environment without proper ventilation.

No response when buttons

pressed.

No operations can be performed

with the remote control.

Play doesn't start (or stops

immediately) when you press [1]

(play).

Cannot select alternative

language. No menu play.

No subtitles.

The position of the subtitles is

incorrect.

Soundtrack and/or subtitle

language is not the one selected

with the SETUP menus.

Cannot change the angle.

The SETUP menu cannot be

accessed.

Cannot add markers.

There are already markers. [RAM]

Marker numbers I added are

different when I call them up. [RAM]

Cannot select random or program play.

Folders deeper than the eighth

layer on a data CD are not

displayed correctly.

You have forgotten your ratings

password.

Reset all the SETUP settings to

Factory Preset.

The unit doesn’t play the data type

(WMA/MP3 or JPEG) selected in

“Mixed disc—Audio & Stills” in

the SETUP menu.

Cannot eject disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic sc dt 310 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic sc dt 310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info