Bedienungsanleitung Panasonic SC-HC302 (Seite 13 von 20) (Englisch)

734662

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

TQBJ2071

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult your

dealer for instructions.

█

Common problems

The unit cannot be switched on.

• Connect the AC mains lead and wait for a minimum of

10 seconds before switching on the unit.

The unit does not work.

• The safety device has been activated. Do the following:

1. Press [1] on the main unit to switch the unit to standby

mode. If the unit does not switch to standby mode,

disconnect the AC mains lead and connect it again.

2. Press [1] again to switch on the unit. If the problem

persists, consult your dealer.

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause, and

then switch on again. It can be caused by straining of the

speakers through excessive volume or power, and when

using the system in a hot environment.

A humming sound can be heard during playback.

• An AC mains lead or fluorescent light is near the cables.

Keep other appliances and cords away from the cables of

this system.

Noise is heard.

• Depending on the device, noise may be heard if the device

is connected to the AUX IN terminal and USB port at the

same time. Disconnect the cable from the USB port.

█

Disc

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

The total number of tracks displayed is incorrect.

The disc cannot be read.

Distorted sound is heard.

• You put in a disc that the system cannot play. Change to a

playable disc.

• You put in a disc that has not been finalised.

█

USB

No response when you press [4/9].

• Disconnect the USB device and then connect it again.

Alternatively, switch the unit off and on again.

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it are not

compatible with the system.

• USB devices with storage capacity of more than 32 GB

cannot work in some conditions.

Slow operation of the USB device.

• Large content size or large memory USB device takes

longer time to read.

The elapsed time shown is different from the actual play

time.

• Transfer the data to another USB device or backup the data

and reformat the USB device.

█

Bluetooth

Pairing cannot be done.

• Check the Bluetooth

device condition.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

The device cannot be connected.

• The pairing of the device was unsuccessful. Do pairing

again.

• The pairing of the device has been replaced. Do pairing

again.

• This system might be connected to a different device.

Disconnect the other device and try connecting the device

again.

• The system may have a problem. Switch off the system and

then switch on again.

• If “MODE 2” is selected in “LINK MODE”, select “MODE 1”.

(

~7)

The device is connected but audio cannot be heard

through the system.

• For some built-in Bluetooth

devices, you have to set the

audio output to “SC-HC302” or “SC-HC300” manually. Read

the operating instructions of the device for details.

Sound from the device is interrupted.

• The device is out of the 10 m communication range.

Move the device nearer to the system.

• Remove any obstacle between the system and the device.

• Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.) are

interfering. Move the device nearer to the system and

distance it from the other devices.

• Select “MODE 1” for stable communication. (~7)

█

Radio, DAB/DAB+

Sound is distorted or static is heard.

• Check that the antenna(s) is properly connected. (~ 4)

• Adjust the position of the antenna.

• Keep a certain amount of distance between the antenna

and the AC mains lead.

• Use an outdoor antenna if there are buildings or mountains

nearby.

• Switch off the TV or other audio players or separate it from

the system.

• Keep the system away from mobile phones if there is

interference.

If there is excessive noise during FM reception.

• Change the audio output to monaural. (~9)

DAB/DAB+ reception is poor.

• Keep the antenna away from computers, TV, other cables

and cords.

█

AUX IN

“AUX-IN Auto Play” does not work.

• You have not connected the external music device correctly.

• Increase the volume of the external music device.

• If “OFF” was selected during “AUX-IN AUTO PLAY”, select

“ON”.

Unintentional automatic switch to AUX source.

• Connect the audio cable to the system only after all the

other connections have been made.

Noise may be detected when connecting the external music

device and it will cause the set to automatically switch to

AUX source.

SC-HC302.300 EB.EG TQBJ2071 En.fm Page 13 Monday, January 8, 2018 11:27 AM

Panasonic SC-HC302 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-HC302

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info