Bedienungsanleitung Panasonic sc ht 1000 (Seite 66 von 68) (Englisch)

370470

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

INFO

RQT7062

Glossary

CPRM (Content Protection for Recordable Media)

CPRM is the copyright protection technology that is used to protect

broadcasts that are allowed to be recorded only once (e.g. some

CATV broadcasts).

Decoder

A decoder restores the coded audio signals on DVDs to normal.

Dolby Digital

This is a method of coding digital signals developed by Dolby

Laboratories. Apart from stereo (2-channel) audio, these signals can

also be multi-channel audio. A large amount of audio information can

be recorded on one disc using this method.

This unit is set to record using Dolby Digital in all recording modes.

Dolby Pro Logic II

Dolby Pro Logic II is an advanced decoder that derives 5 channel

surround (Left, Center, Right, Left and Right Surround) from any

stereo programme material, whether or not it has been specifically

Dolby Surround encoded. Pro Logic II provides two full-range

surround channels, as opposed to Pro Logic’s single surround

channel.

DTS (Digital Theater Systems)

This surround system is used in many movie theaters around the

world. There is good separation between the channels, so realistic

sound effects are possible.

Frame still and field still

Frames are the still pictures that make moving pictures. About thirty

are shown each second. A frame still may appear blurred but overall

quality is high.

Two fields appear alternately to make up one frame. A field still is not

blurred but picture quality is lower.

I/P/B

MPEG 2, the video compression standard adopted for use with

DVD-Video, codes frames using these 3 picture types.

I: Intra coded picture

This picture has the best quality and is the best to use when

adjusting the picture.

P: Predictive coded picture

This picture is calculated based on past I- or P-pictures.

B: Bidirectionally-predictive coded picture

This picture is calculated by comparing past and future I- and

P-pictures so it has the lowest volume of information.

Linear PCM (pulse code modulation)

These are uncompressed digital signals, similar to those found on

CDs. LPCM sound is available when recording in XP mode.

NICAM (NICAM Broadcasting System)

This is a 2 channel sound broadcast system which in most instances

provides high quality stereo sound. Broadcasters can also transmit

two separate mono soundtracks on this system.

Playback control (PBC)

If a Video CD has playback control, you can select scenes and

information with menus.

Pan&Scan/Letterbox

In general, DVD-Video are produced with the intention that they be

viewed on a widescreen television with an aspect ratio of 16:9. This

means you can view most material with the intended aspect ratio on

a widescreen television.

Material with this ratio will not fit onto a standard television with an

aspect ratio of 4:3. Two styles of picture, “Pan&Scan” and

“Letterbox”, deal with this problem.

Pan&Scan: The sides are cut off so the picture

fills the screen.

Letterbox: Black bands appear at the top and

bottom of the picture so the picture

itself appears in an aspect ratio of

16:9.

PDC

PDC (Programme Delivery Control)

Programme Delivery Control adjusts the start and stop time of a

timer recording automatically to ensure the recording starts and

finishes in line with the programme broadcast. This is useful when a

programme over-runs the published times. The station must be

transmitting PDC and the exact time must be set for PDC to work.

The unit detects whether a station is transmitting PDC only during

the tuning process. If PDC is introduced or discontinued by a station

you will need to re-tune the unit before it becomes aware of this.

PDC transmissions are not currently nation-wide so please check

with your local broadcaster for more information. The beginnings of

recordings may not be recorded correctly in some cases.

RGB Output

[RGB] means separate Red/Green/Blue color signals (PAL only). If

you connect a TV equipped with RGB input capability to the AV1

terminal on this unit, and a decoder equipped with RGB output

capability to the AV2 terminal, the TV can receive RGB signal input

from the decoder via the unit.

Message Message appears when:

This programme has already started A timer recording has just started.

Set DVD to timer standby mode The unit is not in the timer standby mode 10 minutes before the programmed recording start time

(message appears every minute during these 10 minutes).

DVD is in timer standby mode [< OPEN/CLOSE] on the main unit or [Í] was pressed, although the unit is in the timer standby mode.

DVD is in timer recording mode [Í], [∫], [¥ REC], [;] or [VIDEO Plus+] was pressed while the unit is in the timer recording mode.

Q Link

This function works only if the unit is connected via a fully wired 21-

pin Scart cable to a TV featuring the Q Link or similar function.

≥Depending on the type of TV used, the messages below may not

appear correctly.

Q Link offers the following functions:

1 Download from the TV

When you connect the unit to a TV, the station list data is

automatically copied from the TV to the unit, and the TV stations

are assigned to the programme positions on the unit in the same

order as on the TV.

2 Direct TV Recording

By simply pressing [¥ DIRECT TV REC], you can at once record

the same programme that you are watching on the TV.

3 TV/DVD Auto On

Even if the TV and the unit are off (standby mode), pressing [1]

(PLAY), [DIRECT NAVIGATOR, TOP MENU], [VIDEO Plus+] or

[PROG/CHECK] automatically turns on both the TV and the unit.

If the TV is off and the unit is on, when you press [FUNCTIONS]

or [1] (PLAY), or insert the disc (except DVD-RAM and DVD-R),

the TV automatically is turned on.

4 DVD Auto Standby

When you turn the TV off, the unit is turned off as well. However,

this function works in the stop mode (except screen saver is

displayed).

This function does not work during the following operations:

Preset Download, Auto-Setup, Auto Clock Setting and Manual

Tuning.

This function also does not work when the selector is on FM/AM.

5 On-Screen Messages

When you are watching a TV programme, the following unit

messages appear on the TV screen to inform you of the unit’s

condition:

These operations are only available if the unit is connected to a TV

featuring the Q Link function.

Panasonic sc ht 1000 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic sc ht 1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info