Bedienungsanleitung Panasonic SC-HTB20 (Seite 25 von 32) (Englisch)

502228

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Operations

VQT4E52

Advanced operations

Change the dual audio from main to secondary.

Confirm the digital audio output setting on the

connected TV or player, etc. is set to “Bitstream”.

2 Press and hold [TV] for more than 2 sec.

3 While the indicator of the current setting is blinking,

press [TV] to change the setting.

≥ The setting works only when the dual audio is

available in the audio source.

≥ The setting is maintained until it is changed again.

≥ The same setting is used for [TV] and [BD/DVD] audio

sources.

This function adjusts the volume automatically when the

volume exceeds a certain level. With this function, you

can prevent sudden loud sounds.

Press and hold [AUX] on remote control for more than

2 sec.

≥ The indicator for the current setting blinks for 10 sec.

2 While the indicator is blinking, press [AUX] to

change the setting.

≥ The setting changes each time [AUX] is pressed.

≥ The setting is maintained until it is changed again.

≥ Default setting of this function is OFF.

Depending on your preference, it is possible to use only

the Dolby Virtual Speaker effect by turning off the 3D

surround effect and the clear-mode dialog effect.

Press and hold [BD/DVD] on remote controller for

more than 2 sec.

≥ The indicator for the current setting blinks for 10 sec.

2 While the indicator is blinking, press [BD/DVD] to

change the setting.

≥ The setting changes each time [BD/DVD] is pressed.

≥ The setting will be reset to on when this system is

turned off.

With this function turned on, this unit can be set to

automatically switch to standby mode if there is no signal

input and no operation is performed for 2 hours.

Press and hold [INPUT SELECTOR] for more than 2

sec.

≥ The indicator for the current setting blinks for 10 sec.

2 While the indicator is blinking, press [INPUT

SELECTOR] to change the setting.

≥ The setting changes each time [INPUT SELECTOR]

is pressed.

≥ The setting is maintained until it is changed again.

∫ Remote control code

When other Panasonic devices respond to this system’s

remote control, change the remote control code on the

active subwoofer and the remote control.

(Continued on the next page)

Changing the dual audio

A : Main

B : Secondary

A, B : Main and secondary

Auto gain control

Dolby Digital indicator blinks:

Auto gain control is on.

PCM indicator blinks:

Auto gain control is off.

To turn off the 3D

surround effect and

clear-mode dialog effect

Dolby Digital indicator blinks:

3D surround effect and

clear-mode dialog effect are on.

PCM indicator blinks:

3D surround effect and

clear-mode dialog effect are off.

Auto standby function

Dolby Digital indicator blinks:

Auto standby function is on.

PCM indicator blinks:

Auto standby function is off.

Others

The following settings are unnecessary under

general usage conditions of the system.

SC-HTB20EBEGGNGS_VQT4E52.book 25 ページ２０１２年２月２４日　金曜日　午後７時５１分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-HTB20 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-HTB20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info