Bedienungsanleitung Panasonic SC-HTB885 (Seite 28 von 36) (Englisch)

618345

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

RQT0A01

There is no audio.

The power of the main unit turns off

automatically.

(When the main unit detects a problem, a safety

measure is activated and the main unit

automatically switches to standby mode.)

≥ There is a problem with the amplifier.

≥ Is the volume extremely high?

If so, lower the volume.

≥ Is this system placed in an extremely hot place?

If so, move this system to a cooler place and

wait a few moments and then try to turn it on

again.

If the problem persists, confirm the display, turn

this system off, remove the AC mains lead cord

and consult your dealer. Please be sure to

remember the display that was indicated and

inform the dealer.

“F61”

≥ There is a problem with the amplifier of the

system.

≥ Disconnect the AC mains lead and consult the

dealer.

“F70 HDMI” / “U701” / “U703”

≥ Check HDMI connection.

≥ Turn off the main unit and then switch it on

again.

≥ Disconnect the HDMI cable.

“F76”

≥ There is a problem with the power supply.

≥ Disconnect the AC mains lead and consult the

dealer.

“U704”

≥ This system is receiving unsupported video

format signal from the input source.

jChange the video resolution setting on the

connected device. (Refer to the operating

instructions for the device.)

jIf there is no image, connect the device

directly to the TV to change the settings.

“U705”

≥ The TV’s HDMI terminal connected to the main

unit or the TV’s setting is not compatible with the

HDCP 2.2 playback source.

jEnsure to connect to the TV’s HDCP 2.2

compatible terminal.

jEnsure the TV’s HDMI HDCP setting

corresponds to HDCP 2.2.

(Refer to the operating instructions for the TV.)

No power.

Ensure the AC mains lead of the active subwoofer

is connected properly.

After turning the subwoofer on, it immediately

turns off.

Unplug the AC mains lead and consult your

dealer.

No sound from the subwoofer.

≥ Check that the active subwoofer is turned on.

≥ Check that the WIRELESS LINK indicator lights

green. (> 19)

The WIRELESS LINK indicator lights red.

≥ There is no link between the main unit and the

active subwoofer.

jCheck that the main unit is turned on.

jTurn the active subwoofer off and then back

on. Alternatively, turn the active subwoofer off,

disconnect the AC mains lead and then

reconnect it.

≥ The active subwoofer and the main unit may not

be paired correctly. Try the following operation.

(Wireless pairing)

1 Turn on the main unit and active subwoofer.

2 Press and hold [ID SET] on the rear of the

active subwoofer for more than 3 sec.

(The WIRELESS LINK indicator will blink in

red.)

3 While pressing and holding [INPUT] on

remote control, touch and hold [VOL i] on

the main unit for more than 4 sec.

(“SUBWOOFER PAIRING” will be indicated

on the display.)

≥ When the wireless pairing is successful, “PAIRED”

will be indicated on the display for 2 sec and

WIRELESS LINK indicator lights green.

4 Turn the main unit off and on.

≥ Consult your dealer if the problem persists.

Main unit displays

Active Subwoofer

SC-HTB885EGEB_RQT0A01-1B.book 28 ページ２０１５年３月９日　月曜日　午後８時３１分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-HTB885 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-HTB885

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info