Bedienungsanleitung Panasonic SC-NE1 (Seite 9 von 40) (Englisch, Polnisch)

618356

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

VQT4U48

ENGLISH

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or if

the solutions indicated in the following guide do not

solve the problem, consult your dealer for instructions.

Humming heard during play.

≥ An AC mains lead or fluorescent light is near the cords. Keep

other appliances and cords away from this unit’s cables.

Pairing cannot be done.

≥ Check the Bluetooth

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the registration has

been replaced. Try pairing the device again.

≥ This unit might be connected to a different device. Disconnect the

other device and try pairing the device again.

The device is connected but audio cannot be heard

through this unit.

≥ For some built-in Bluetooth

devices, you have to set the audio

output to “SC-NE1” manually. Read the operating instructions for

the device for details.

The sound is interrupted.

≥ The device is out of the 10 m communication range. Bring the

Bluetooth

device closer to this unit.

≥ Remove any obstacle between this unit and the device.

≥ Other devices that use the 2.4 GHz frequency band (wireless

router, microwaves, cordless phones, etc.) are interfering. Bring

the Bluetooth

device closer to this unit and distance it from the

other devices.

≥ Select “MODE 1” for stable communication. (l 6)

The remote control doesn’t work properly.

≥ The remote control and this unit are using a different code.

(l below, “REMOTE ”)

≥ Is the battery depleted or is the battery inserted incorrectly? (l 4)

The following messages or service numbers may

appear on the unit’s display.

“AUTO OFF”

≥ The unit has been left unused for about 30 minutes and will shut

down within a minute. Press any button to cancel it.

“ERROR”

≥ Incorrect operation is performed. Read the instructions and try

again.

“F ” (“  ” stands for a number.)

≥ There is a problem with this unit.

Note down the displayed number, disconnect the AC mains lead

and consult your dealer.

“REMOTE ” (“  ” stands for a number.)

≥ The remote control and this unit are using different codes. Change

the code on the remote control.

– When “REMOTE 1” is displayed, press and hold [OK] and

[ , AUX] for more than 4 seconds.

– When “REMOTE 2” is displayed, press and hold [OK] and

[SOUND] for more than 4 seconds.

To return all settings to the factory preset

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ Keep holding down [Í/I] until “--------” appears

on the display.

3 Release [Í/I].



≥ All the settings are returned to the factory preset. You will

need to reset the memory items.

Common problems

Bluetooth

Remote control

Messages

SC-NE1_EG~VQT4U48.book 9 ページ２０１３年１月１５日　火曜日　午後１時４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-NE1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-NE1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info