Bedienungsanleitung Panasonic SC-PMX100 (Seite 18 von 24) (Englisch)

618452

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

RQT9995

To check this system’s IP address or the Wi-Fi MAC

address.

1 Press [RADIO, EXT-IN] repeatedly to select

“Network”.

2 Press [SETUP] repeatedly to select “Net Info”

and then press [OK].

3 Press [3, 4] to select “IP Addr.” or “MAC Addr.”

and then press [OK].

The IP address or the MAC address is partially

displayed.

4 Press [2, 1] on the remote control to show the

rest of the IP address or the MAC address.

• Press [OK] to exit.

• The “ – ” displayed on the top or bottom left of the

display indicate the first and last units respectively.

To reset the network settings.

1 Press [RADIO, EXT-IN] repeatedly to select

“Network”.

2 Press [SETUP] repeatedly to select “Net Reset”

and then press [OK].

3 Press [2, 1] to select “OK? Yes” and then press

[OK].

• Wait for “Network Initializing” to stop scrolling.

• “WAC Mode” will be indicated on the display.

– “Method 1” of network setting method is available.

(> 6)

– To exit “WAC Mode”, press [∫].

• This function does not affect the “Wireless LAN” setting.

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult

your dealer for instructions.

For further dedicated help, support and advice about

your product please visit:

http://panasonic.jp/support/global/cs/audio/

(This site is in English only.)

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the

cause, then switch the system on again. It can be

caused by straining of the speakers through excessive

volume or power, and when using the system in a hot

environment.

• Ensure the speaker cables are connected correctly

and securely. (> 4)

A “humming” sound can be heard during playback.

• An AC mains lead or fluorescent light is near the

cables. Keep other appliances and cords away from

the cables of this system.

The unit does not work.

• One of the unit’s safety devices may have been

activated.

Reset the unit as follows:

1 Press [Í/I] on the unit to switch the unit to standby.

• If the unit does not switch to standby, press [Í/I] on

the unit for approximately 10 seconds. The unit is

forcibly switched to standby. Alternatively, disconnect

the AC mains lead, wait for at least 3 minutes, then

reconnect it.

2 Press [Í/I] on the unit to switch it on. If the unit still

cannot be operated, consult the dealer.

Noise is heard.

• During “AUX” mode, when a device is connected to

both the AUX IN terminals and the USB port, noise

may be generated depending on the device. In this

case, remove the USB cable from the USB port.

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or

non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

Reception is poor or a beat sound is heard.

• Keep the antenna away from computers, TVs, other

cables and cords.

• Use an outdoor antenna.

• Switch off the TV or move it away from the system.

If noise is excessive during FM reception.

• Change the audio to be output as monaural.

1 Press [RADIO MENU] repeatedly to select “FM Mode”.

2 Press [2, 1] to select “Mono” and then press [OK].

The sound becomes monaural.

• To cancel, select “Stereo” or change the frequency.

In normal circumstances, select “Stereo”.

Cannot charge or operate.

• Check that the iPhone/iPad/iPod is connected

properly.

• Connect the iPhone/iPad/iPod again or try to restart

the iPhone/iPad/iPod.

• During standby mode, charging will not start from the

USB cable connection.

Turn this unit on and make sure the charging has

started before turning this unit to standby mode.

• The battery of the iPhone/iPad/iPod is depleted.

Charge the iPhone/iPad/iPod, and then operate again.

– When using the port, turn this unit on. Do not turn this

unit off until the iPhone/iPad/iPod becomes operational.

IP/MAC Address

Network reset

Do you have the latest software installed?

Panasonic is constantly improving the system’s

software to ensure that our customers are enjoying

the latest technology. (> 17)

Common problems

Disc

Radio

iPhone/iPad/iPod

SC-PMX100-100B_EGEBGN-RQT9995-B.book 18 ページ２０１５年４月２０日　月曜日　午後３時４５分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-PMX100 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-PMX100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info