Bedienungsanleitung Panasonic sc pt470 (Seite 32 von 40) (Englisch)

371548

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

RQTX0216

Getting StartedPlaying DiscsOther OperationsReference

Troubleshooting guide

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated in the following guide do not solve the

problem, consult your dealer for instructions.

No power.

Insert the AC mains lead securely. (B 8)

The unit is automatically switched to standby mode.

The Sleep timer was working and had reached the set

time limit. (B 38)

The display is dark.

Select “BRIGHT” in “FL DIMMER” in the OTHERS menu.

(B 28)

“NO PLAY”

≥You inserted a disc the unit cannot play; insert one it

can. (B 30)

≥You inserted a blank disc.

≥You inserted a disc that has not been finalized.

“NO DISC”

≥You have not inserted a disc; insert one.

≥You have not inserted the disc correctly; insert it

correctly. (B 14)

“OVER CURRENT ERROR”

The USB device is drawing too much power. Switch to

DVD/CD mode, remove the USB and turn the unit off.

“IPOD OVER CURRENT ERROR”

The iPod is drawing too much power. Remove the iPod,

and turn the unit off and on again.

“F61”

Check and correct the speaker cable connections. If this

does not fix the problem, consult the dealer. (B 6)

“F76”

There is a power supply problem. Consult the dealer.

“DVD U11”

Disc may be dirty. Wipe it clean. (B 31)

“ERROR”

Incorrect operation performed. Read the instructions and

try again.

“DVD H∑∑”

“DVD F∑∑∑”

∑ stands for a number.

≥Trouble may have occurred. The numbers following “H”

and “F” depend on the status of the unit. Turn the unit

off and then back on. Alternatively, turn the unit off,

disconnect the AC mains lead, and then reconnect it.

≥If the service numbers fail to clear, note the service

number and contact a qualified service person.

“U70∑”

∑ stands for a number. (The actual number following

“U70” will depend on the state of this unit.)

≥The HDMI connection acts unusually.

–The connected equipment is not HDMI-compatible.

–Please use HDMI cables that have the HDMI logo (as

shown on the cover).

–The HDMI cable is too long.

–The HDMI cable is damaged.

“REMOTE 1” or “REMOTE 2”

Match the modes on this unit and remote control.

Depending on the number being displayed (“1” or “2”),

press and hold [OK] and the corresponding numbered

button ([1] or [2]) for at least 2 seconds. (B 38)

“LOADING”

≥The iPod is not ready. Wait for this display to disappear.

≥

Disconnect the iPod, and then reconnect it firmly. (

22)

“NO MIC”

The Auto speaker setup microphone is not inserted.

Check whether the Auto speaker setup microphone is

plugged in properly into the SETUP MIC jack.

“NOISY”

Excessive ambient noise in the room. Perform the setup

again and keep quiet during the Auto speaker setup.

No response when any buttons are pressed.

≥This unit cannot play discs other than the ones listed in

these operating instructions. (B 30)

≥The unit may not be operating properly due to lightning,

static electricity or some other external factor. Turn the

unit off and then back on. Alternatively, turn the unit off,

disconnect the AC mains lead, and then reconnect it.

≥Condensation has formed. Wait 1 to 2 hours for it to

evaporate.

No response when remote control buttons are

pressed.

≥Check that the batteries are installed correctly. (B 8)

≥The batteries are depleted. Replace them with new

ones. (B 8)

≥Aim the remote control at the remote control signal

sensor and operate. (B 39)

Other products respond to the remote control.

Change the remote control operating mode. (B 38)

No picture or sound.

≥Check the video or speaker connection. (B 6, 7)

≥Check the power or input setting of the connected

equipment and this unit.

≥Check that the disc has something recorded on it.

You have forgotten your ratings password.

Reset all the settings to Factory Preset.

While stopped and “DVD/CD” is the source, press and

hold [∫] (Stop) on this unit and [S10] on the remote

control until “INITIALIZED” disappears from the TV. Turn

the unit off and on again.

All settings will return to the default values.

(This does not work during program and random modes,

or when setup menu or START menu is displayed.)

Some characters are not displayed correctly.

Characters other than English alphabet and Arabic

numerals may not be displayed correctly.

The VIERA Link “HDAVI Control” function does not

respond.

Depending on the condition of this unit or the connected

equipment, it may be necessary to repeat the same

operation so that the function can work correctly. (B 24)

Power

Unit displays

General operation

SC-PT470EB-RQTX0216-B_eng.book Page 32 Monday, December 22, 2008 3:28 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic sc pt470 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic sc pt470

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info