Bedienungsanleitung Panasonic SC-SB1 (Seite 11 von 136) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

734652

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Operations

TQBS0132

Bluetooth

connection

By using the Bluetooth

connection, you can listen

to the sound from the Bluetooth

audio device

from this system wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device

for further instruction on how to connect a Bluetooth

device.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near this system.

1 Press [ ] to select “ ”.

≥ If the “ ” indicator flashes quickly, go to step 3.

2 Press and hold [ ] until the “ ” indicator

flashes quickly.

≥ If the “ ” indicator flashes slowly, repeat step 2.

3 Select “SC-SB1” from the Bluetooth

device’s Bluetooth

menu.

≥ If prompted for the passkey on the Bluetooth

device,

enter “0000”.

≥ Once the Bluetooth

device is connected, the “ ”

indicator stops flashing and lights up.



≥ You can register up to 8 devices with this system. If a 9th

device is paired, the device that has not been used for the

longest time will be replaced.

1 Press [ ] to select “ ”.

≥ If the “ ” indicator lights, a Bluetooth

device is

already connected with this system. Disconnect it.

(> below)

2 Select “SC-SB1” from the Bluetooth

device’s Bluetooth

menu.

∫ Disconnecting a Bluetooth

device

Press and hold [ ] until the “ ” indicator flashes.



≥ This system can only be connected to one device at a time.

Advanced operations

This system is automatically turned off if there is no audio

input and when you do not use it for approx. 19 min and

30 sec.

1 While pressing

and holding

[i SUBWOOFER]

on the remote control, press and hold

[VOL s] on this system for more than

4 sec.

≥ The current mode will be indicated by the

corresponding LED indicator.

2 While the current mode is indicated (about

20 sec), press [i SUBWOOFER] again.

≥ The setting changes each time [i SUBWOOFER] is

pressed.

≥ The indicator for the selected setting blinks for 20 sec and

then exits the setting mode.

≥ The setting is maintained until it is changed again.

≥ Default setting of this function is “On”.

This function allows you to connect a paired Bluetooth

device when this system is in standby mode.

1 While pressing

and holding

[SUBWOOFER j]

on the remote control, press and hold

[VOL s] on this system for more than

4 sec.

≥ The current mode will be indicated by the

corresponding LED indicator.

2 While the current mode is indicated (about

20 sec), press [SUBWOOFER j] again.

≥ The setting changes each time [SUB WOOFER j] is

pressed.

≥ The indicator for the selected setting blinks for 20 sec and

then exits the setting mode.

≥ The setting is maintained until it is changed again.

≥ Default setting of this function is “On”.

Bluetooth

pairing

Connecting a paired Bluetooth

device

Auto Power Down

Bluetooth

Standby

“On” “Off”

(11)

SC-SB1_EG_TQBS0132.book 11 ページ２０１７年４月２１日　金曜日　午後３時３２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-SB1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info