Bedienungsanleitung Panasonic SC-TMAX50 (Seite 17 von 116) (Englisch, Dänisch, Polnisch, Schwedisch, Finnisch)

735115

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

Confidential

Until:

02 Aug 2019

TQBJ2193

█

Unit displays

“--:--”

• You connected the AC mains lead for the first time or there

was a power failure recently. Set the clock.

• Track play time is more than 99 minutes.

“ADJUST CLOCK”

• The clock is not set. Adjust the clock.

“ADJUST TIMER”

• The play timer is not set. Adjust the play timer.

“AUDIO UNSUPPORTED”

• The signal format or frequency is not supported.

• This system does not support bitstream signals. Change the

digital audio output setting on the external equipment to

PCM.

• This system supports sampling frequencies of 32 kHz,

44.1 kHz, 48 kHz, up to 96 kHz. Select only the supported

sampling frequencies on the connected equipment.

• Try connecting the external equipment by using the auxiliary

input.

“AUTO OFF”

• The system has not been used for 20 minutes and will

switch off within a minute. To cancel, press any button.

“DEVICE CONNECTED FULL”

• You have connected 3 Bluetooth

devices. To connect

another device, disconnect one of the connected devices

and try again.

“ERROR”

• An incorrect operation was done. Read the instructions and

try again.

“F” / “F” (“” represents a number.)

• The protection circuit has been activated and the system

may be switched off automatically.

• Disconnect the AC mains lead and wait for a few seconds

before connecting it again. If the problem persists,

disconnect the AC mains lead and consult your dealer.

“NO DISC”

• You have not put in a disc.

“NO PLAY”

“UNSUPPORT”

• There is no album or track in the USB device.

• Examine the content. You can only play supported format.

• The files in the USB device can be corrupted. Format the

USB device and try again.

• The system may have a problem. Switch off the system and

then switch on again.

“NOT SUPPORT MULTI CONNECT”

• The Bluetooth

connection cannot be established.

Disconnect the existing connected devices and try again.

“NOT SUPPORTED”

• To use Karaoke effect in D-IN source, change the digital

audio output setting on the external equipment to PCM.

“PLAYERROR”

• An unsupported MP3 file has been played. The system will

skip that track and play the next one.

“REMOTE 1”

“REMOTE 2”

• The remote control and the unit are using different codes.

Change the code of the remote control.

– When “REMOTE 1” is shown, press and hold [OK] and

[ ] on the remote control for a minimum of 4 seconds.

– When “REMOTE 2” is shown, press and hold [OK] and [<]

for a minimum of 4 seconds.

“USB A NO DEVICE”

“USB B NO DEVICE”

• The USB device is not connected. Examine the connection.

“USB OVER CURRENT ERROR”

• The USB device is drawing too much power. Disconnect the

USB device, switch off the system and then switch on again.

• Check the connection, it may be caused by a faulty USB

cable.

“VBR”

• The system cannot show the remaining play time for variable

bit rate (VBR) tracks.

ENGLISH

TMAX40.50E_TQBJ2193_En.Sw.Da.Fi.Po.Cz.book Page 17 Tuesday, July 16, 2019 10:45 AM

offset printing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-TMAX50 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-TMAX50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info