Bedienungsanleitung Panasonic sc zt1 (Seite 16 von 32) (Englisch)

419481

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

RQT9472

When the speakers are detected, the Wireless Link display lights up on the main unit’s

display.

(Blinks during detecting operation.)

While the wireless speakers operate normally, the Wireless Link display lights, but when radio

waves are interrupted (when speakers are in standby condition, etc.), it blinks.

Display

Wireless Link

display

Speaker setting

• When you turn the main unit off with the speakers on, the speakers automatically enter standby (Wireless link standby). The

colour of [WIRELESS LINK] indicator turns to red.

• To reduce more of the power consumption of speakers in standby, turn the speakers off. The speakers enter standby (In standby

condition).

Wireless link standby: approx. 0.8 W (per 1 speaker)

In standby condition: approx. 0.15 W (per 1 speaker)

Speaker setting

Connection

Checking the speaker setting

1. Turn the main unit on.

2. Press [TEST] on the remote

control to output the test signal.

3. Make sure that the display of main unit matches speaker locations.

The test signal is output from one speaker at a time for about 2 seconds in the order shown below.

“TEST L ”

→

“TEST R ”

→

“TEST RS ”

✽

→

“TEST LS ”

✽

 Conﬁ rm the correct setting locations in the following chart.

Display Speaker outputting the test signal

TEST L Front left

TEST R Front right

TEST RS

✽

Surround right (right back)

TEST LS

✽

Surround left (left back)

If the speakers are not properly set, do either of the following.

• Move the speakers according to the unit’s display.

• Perform steps 3 and 4 of “Setting the speakers” (➜ page 15). When using the surround speakers, perform steps 7 and 8 of

“Setting surround speakers” (

➜

page 17).

4. Press [TEST] on the remote control to stop the test signal.

If the speaker is repaired or replaced

Perform the above “Checking the speaker setting” to conﬁ rm that the speaker properly operates.

Do the following operations if the sound is not produced normally.

1. Press and hold [INPUT SELECTOR] on the main unit approx. 3 seconds until “2CH SEARCH ” is displayed.

2. Perform steps 2 to 4 of “Setting the speakers” (

➜

page 15).

Installing surround speakers

You can enjoy more dynamic surround playback with this system by installing Panasonic surround speakers SB-ZT1.

Note

✽ Displayed only when using

the surround speakers.

Press

• To adjust the speaker volume, press [VOL +, –].

Setup example

Front speaker

(right)

Front speaker

(left)

Connected equipment

Main unit

The surround speakers are not included.

Surround

speaker

(left)

Surround

speaker (right)

Approx. 120°

• Place them slightly at the back right and left of the listening-viewing

position.

• There is no positional distinction for each speaker before setting.

• Aim the front face (with Panasonic logo) of each speaker at the listening-

viewing position for setting.

Set the distance from each speaker to the listening-viewing

position. (

➜

page 24)

Note

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic sc zt1 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic sc zt1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info