Bedienungsanleitung Panasonic SCALL30TEG (Seite 24 von 40) (Englisch)

612774

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

SQT0936



≥ The default setting is underlined. Changed settings will

be kept until it is changed again, unless otherwise

indicated.

REAR

SPEAKER

You can select to have 4.1 ch

output with rear surround speakers

(ON) or 2.1 ch output without rear

surround speakers (OFF).

OFF

REAR LEVEL

You can adjust the output level of

the rear surround speakers. Pair

SC-ALL2 (sold separately) with this

system beforehand. (

25)

1 Press [4][3] to select the output

level of the left surround speaker

and press [OK]. (REAR L)

2 Press [4][3] to select the output

level of the right surround speaker

and press [OK]. (REAR R)

≥

You can adjust the output level between

6 and

6. The default setting is 0.

≥ If only one rear surround speaker

has been paired or if both are set

in the same channel, either “REAR

L” or “REAR R” is displayed.

≥

“REAR LEVEL” is not indicated on the

display when “REAR SPEAKER” is set

to “OFF” or a rear surround speaker is

not linked to this system.

NET SETUP

You can choose how to

connect to a network.

≥ For details, refer to “Network

settings” (> 12)

NET INFO

You can confirm the IP

address allocated to this

system, the MAC address of

this system, and the network

name (SSID) of this system.

IP ADDR

MAC ADDR

SSID

≥ Characters that cannot be

displayed are replaced with “ ＊ ”.

SIGNAL

LEVEL

You can check the signal strength

of the wireless connection.

≥

The signal strength is displayed when

you press [OK] while “SIGNAL LEVEL”

is being displayed.

Press [OK] again to stop the display.

≥

It is recommended to have a signal

strength of “LEVEL 3”. Change the

position or angle of your wireless

network router or this system if the

indication is “LEVEL 2” or “LEVEL 1”

and see if the connection improves.

≥ If “LEVEL 0” is displayed, this

system cannot establish a link with

the wireless network router.

≥ “WIRED LAN” is displayed when

connected with a LAN cable.

NET

STANDBY

This system can turn on

automatically from standby

mode when this system is

selected as the AllPlay/DLNA

speakers.

≥ This function normally switches to

“ON” while this system is

connected to a network.

– To turn off this function, select

“OFF” and then select a source

other than “NETWORK” before

switching this system to standby

mode.

OFF

≥ If this function is set to “ON” the

standby power consumption will

increase.

≥ When the system is turned on by

this feature, the beginning part of

the music may not be played back.

≥ Depending on the app, the

conditions for activating this

function may differ.

≥

The system may not turn on even

when selected as the output speakers.

In that case, start playback.

WIRELESS

LAN

The wireless LAN function

can be enabled or disabled.

OFF

F/W VERSION

You can check the firmware

version.

≥ The version of the installed

firmware is displayed when you

press [OK] while “F/W VERSION”

is being displayed.

Press [OK] again to stop the

display.

F/W UPDATE

You can update the firmware

of this system.

≥ For details, refer to “Firmware

update” (> 25)

SC-ALL30T-SQT0936.book 24 ページ２０１５年４月２８日　火曜日　午前１０時０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCALL30TEG Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCALL30TEG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info