Bedienungsanleitung Panasonic SCCMAX5E (Seite 17 von 64) (Englisch, Polnisch)

608348

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

RQT0A52

ENGLISH

Occasionally, Panasonic may release updated

software for this unit that may add or improve the

way a feature operates. These updates are

available free of charge.

For more details, refer to the following website.

http://panasonic.jp/support/global/cs/

(This site is in English only.)

∫ Checking the software version

The version of the installed software is displayed.

Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

≥ Press [OK] to exit.

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

Preparation

Press [AUX] to select “AUX 1” or “AUX 2”.

∫ To set the code to “REMOTE 2”

1 While pressing and holding [USB] on the unit,

press and hold [AUX] on the remote control

until the unit’s display shows “REMOTE 2”.

2 Press and hold [OK] and [USB] on the remote

control for at least 4 seconds.

∫ To set the code to “REMOTE 1”

1 While pressing and holding [USB] on the unit,

press and hold [USB] on the remote control

until the unit’s display shows “REMOTE 1”.

2 Press and hold [OK] and [ ] on the remote

control for at least 4 seconds.

Troubleshooting

Before requesting service, make the following

checks. If you are uncertain about some of the

check points, or if the solutions indicated in the

following guide does not resolve the issue, then

consult your dealer for instructions.

Humming heard during playback.

≥ If an AC mains lead or fluorescent lights are near

the cords, then keep other appliances and cords

away from the cables.

The unit does not work.

≥ One of the unit’s safety devices may have been

activated.

Reset the unit as follows:

1 Press [Í/I] on the unit to switch the unit to

standby.

≥ If the unit does not switch to standby, press

[Í/I] on the unit for approximately

10 seconds. The unit is forcibly switched to

standby. Alternatively, disconnect the AC

mains lead, wait for at least 3 minutes, then

reconnect it.

2 Press [Í/I] on the unit to switch it on. If the

unit still cannot be operated, consult the

dealer.

The display panel lights up and changes

continuously in standby mode.

≥ Press and hold [∫] on the unit to select “DEMO

OFF”.

Software update

Remote control code

To return all settings to the factory defaults

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at

least 3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ Keep holding down [Í/I] until “--------” appears on the

display.

3 Release [Í/I].



≥ All the settings are returned to the factory defaults. You will

need to reset the memory items.

General

SC-CMAX5_E~RQT0A52-R.book 17 ページ２０１５年６月１２日　金曜日　午前１１時２２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCCMAX5E Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCCMAX5E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info