Bedienungsanleitung Panasonic SCHC37EC (Seite 12 von 44) (Englisch, Polnisch)

608415

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

RQT9685

Others

As a factory preset, this unit will always turn off

automatically if there is no sound output and no

operation for 30 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”

and then press [OK].

2 Press [3, 4] to select “OFF” and then press [OK].



≥ To turn automatic standby on, select “ON” in step 2.

≥ This setting cannot be selected when “FM” is the source.

The brightness of this unit’s display can be changed.

1 Press [SETUP] repeatedly to select “DIMMER”

and then press [OK].

2 Press [3, 4] to select “ON” and then press [OK].



To cancel the dimmer, select “OFF” in step 2.

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

1 Press [CD] to select “CD”.

2 Press and hold [CD] on the main unit and [3] on

the remote control until the main unit’s display

shows “REMOTE 2”.

3 Press and hold [OK] and [3] on the remote control

for at least 4 seconds.



To change the mode back to “REMOTE 1”, repeat the steps

above by replacing [3] with [4].

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or if

the solutions indicated in the following guide do not

solve the problem, consult your dealer for instructions.

Humming heard during play.

≥ An AC mains lead or fluorescent light is near the cords. Keep

other appliances and cords away from this unit’s cables.

MP3 cannot be read.

≥ You may not be able to play MP3 if you have copied a

multi-session disc that has no data between sessions.

≥ When creating a multi-session disc, it is necessary to close the

session.

≥ The amount of data on the disc is too small. Set the amount of

data to above 5 MB.

Incorrect display or play will not start.

≥ Make sure that the disc is compatible with this unit.(> 4)

≥ There is moisture on the lens. Wait for about an hour and then try

again.

No response when [1/;] is pressed.

≥ Disconnect the USB device and then reconnect it. Alternatively,

turn the unit off and on again.

The USB drive or its contents cannot be read.

≥ The USB drive format or its contents is/are not compatible with the

unit. (> 4)

≥ The USB host function of this product may not work with some

USB devices.

Automatic standby

Display brightness

Changing the main unit and

remote control code

To return all settings to the factory preset

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

main unit, reconnect the AC mains lead.

≥ “--------” appears on the display.

3 Release [Í/I].



All the settings are returned to the factory preset. You will

need to reset the memory items.

Common problems

Disc operations

USB operations

SC-HC37~RQT9685.book Page 12 Friday, February 24, 2012 9:45 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHC37EC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCHC37EC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info