Bedienungsanleitung Panasonic SCHT920 (Seite 5 von 36) (Englisch)

18718

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

RQT7696

Front speaker assembly/Other speaker setup options

4 Connect the speaker cables.

5 Fasten the speaker cable to the base.

≥Using the same polyfoam as in procedure 2 will assist you in

safely and securely fastening the speaker cables.

∫ Preventing the speakers from falling over

Preparation

Attach screw eyes (not included) to secure the speakers to the wall

(‹diagram below)

≥You will need to obtain the appropriate screws to match the walls

and pillars to which the screw eyes are going to be fastened.

≥Consult with a qualified housing contractor concerning the

appropriate procedure when attaching to a concrete wall or a

surface that may not have strong enough support. Improper

attachment may result in damage to the wall or speakers.

1 Thread the string (not included) through the slot on the

rear of the speaker to prevent it from falling over.

2 Loop the string through the screw eye and tie tightly.

Other speaker setup options

∫ Attaching to a wall

1 Drive a screw (not included)

into a wall.

2 Fit the speaker securely onto

the screw(s) with the hole(s).

≥

The wall or pillar on which the speakers are to be attached should be

capable of supporting 10 k

(22 lb.) per screw. Consult a qualified

building contractor when attaching the speakers to a wall. Improper

attachment may result in damage to the wall and speakers.

≥When mounting the front speaker to a wall, we recommend using

a string (not included) to prevent it from falling ( ‹ left).

≥Use of optional speaker cables is recommended for wall mounted

front speakers. (You can also remove the speaker cables from the

pipes supplied with this system).

e.g.

Front speaker Center speaker

∫ Fitting speaker stands (not included)

Ensure the stands meet these conditions before purchasing them.

Note the diameter and length of the screws and the distance

between screws as shown in the diagram.

≥The stands must be able to support over 10 kg (22 lb.).

≥

The stands must be stable even if the speakers are in a high position.

e.g. Surround speaker

Rear of the speaker

_: Copper

`: Silver

Push !

If there is any excess

speaker cable, thread the

speaker cable into the

opening near the top of the

pipe while pulling the

speaker cable from the

bottom of the base.

Twist off the vinyl ends of the

speaker cables.

2 Press the speaker cable into the groove.

2 Fit the speaker

cable into the

base cover groove

as far as possible.

1 Press the speaker

cable and thread

between the

hooks.

Rear side of base

Cable

String (not included)

Wall

Screw eye (not included)

Rear of the speaker

Approx. 150 mm

/16z)

e.g.

30–35 mm

/16q–1

/8q)

‰7.5–9.4 mm

(

/64q–

/8q)

8–11 mm

(

/8q–

/16q)

230 mm

/16z)

150 mm

/32z)

In this position, the

speaker will likely

fall if moved to the

left or right.

Move the speaker

so the screw is in

this position.

Speaker stand

(not included)

5 mm (

/64z),

pitch 0.8 mm (

/32z)

60 mm (2

/64z)

Plate thickness plus 7 to 10 mm

(plus

/32z to

/64z)

Attach the stands to

these metal screw

holes.

Wall or pillar

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHT920 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info