Bedienungsanleitung Panasonic SCMAX4000 (Seite 8 von 124) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

618354

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

RQT0A38

Preparing media

Disc

1 Press [CD x] (main unit: [x OPEN/CLOSE]) to

open the disc tray.

Put in a disc with the label facing up.

Press again to close the disc tray.

2 Press [CD/RADIO/AUX] to select “CD”.

USB

Preparation

Before you connect a USB device to the system, make

sure you do a backup of the data.

1 Decrease the volume and connect the USB device

to the USB port.

Hold the main unit when connecting or disconnecting

the USB device.

2 Press [USB] (main unit: [MEMORY/USB]) to select

“USB A” or “USB B”.

USB status indicator lights up in red when selected.

Note:

Do not use a USB extension cable. The system cannot

recognise USB device connected through a cable.

Bluetooth

You can connect and play an audio device wirelessly

through Bluetooth

Preparation

• Switch on the Bluetooth

feature of the device and put

the device near the system.

• Read the operating instructions of the device for

details.

█ Pairing a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it (Z“Disconnecting a device”).

1 Press [ ].

If “PAIRING” is shown, continue with step 4.

2 Press [PLAY MENU] to select “PAIRING”.

3 Press [Y, U] to select “OK? YES” and then press

[OK].

“PAIRING” is shown.

To cancel, select “OK? NO”.

4 Select “SC-MAX4000” from the Bluetooth

of the device.

If prompted for a passkey, input “0000”.

The device connects with this system automatically

after pairing is complete.

The name of the connected device is shown for a few

seconds.

Using the main unit

1 Press and hold [ –PAIRING] until “PAIRING” is

shown.

2 Select “SC-MAX4000” from the Bluetooth

of the device.

Note:

You can pair up to 8 devices with this system. If a 9th device

is paired, the device that has not been used for the longest

time will be replaced.

█ Connecting a device

Preparation

If this system is connected to a Bluetooth

device,

disconnect it (Z“Disconnecting a device”).

1 Press [ ].

“BLUETOOTH READY” is shown.

2 Select “SC-MAX4000” from the Bluetooth

of the device.

The name of the connected device is shown for a few

seconds.

3 Start playback on the device.

Note:

• A device must be paired to connect.

• This system can only connect to one device at a time.

• When “BLUETOOTH” is selected as the source, this

system will automatically try to connect to the last

connected device. (“LINKING” is shown during this

process.)

█ Disconnecting a device

1 Press [ ].

2 Press [PLAY MENU] to select “DISCONNECT?”.

3 Press [Y, U] to select “OK? YES” and then press

[OK].

“BLUETOOTH READY” is shown.

To cancel, select “OK? NO”.

Using the main unit

Press and hold [ –PAIRING] until “PAIRING” is

shown.

Note:

A device is disconnected when you:

• Select a different source.

• Move the device out of the maximum range.

• Disable the Bluetooth

transmission of the device.

• Switch off the system or the device.

MAX4000E.book Page 8 Tuesday, April 21, 2015 4:57 PM

offset printing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCMAX4000 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info