Bedienungsanleitung Panasonic SCPM39D (Seite 37 von 40) (Englisch)

618440

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

RQT7502

Reference

Picture

Picture distorted.

No picture.

The picture shown on the television

is not normal.

(The sides of the picture are

cut off, the picture is stretched

horizontally, or black bands appear

at the top and bottom

of the screen.)

For Saudi Arabia, Kuwait, the Middle East

and

Southeast Asia

There is ghosting when

progressive output is on.

Picture quality is poor.

The picture on the television

disappears or stripes appear

on the screen.

Menus not displayed correctly.

•

Some distortion is normal during SEARCH.

•

Check the connection.

•

Make sure the television is on.

•

Ensure the television’s video input setting (e.g., VIDEO 1) is correct.

•

Go to “Video” tab in the SETUP menus, and change “TV Aspect” to suit your television.

•

Use the television to change the aspect to the correct one.

If your television cannot change the aspect when input is progressive, try

changing 4:3 Aspect in Display Menu.

•

Ensure that the unit is connected directly to the television, and is not connected

through a video cassette recorder.

•

Change the size with the zoom function.

•

Connect to the component video (480P) input terminals on a television compatible

with this unit’s copy guard system. You cannot view progressive video if your

television is not compatible.

•

Change “Video Output Mode” to “480I” so “PROGRESSIVE” on the display goes

out. This problem is caused by the editing method or material used on DVD-Video,

but should be corrected if you use interlace output.

•

Check the settings in Picture Menu.

•

Mobile telephone chargers can cause some disturbance.

•

The location and orientation of the antenna are incorrect. If you are using an

indoor antenna, change to an outdoor antenna.

•

The television antenna wire is too close to the unit. Separate the antenna wire of

the television from the unit.

•

Change the zoom ratio to “x1.00”.

•

Set “Subtitle Position” in Display Menu to “0”.

•

Set “4:3 Aspect” in Display Menu to “Normal”.

Sound

No sound.

Distorted sound.

Piercing noise comes from the

speakers.

•

Check the connections.

•

Turn the volume up.

•

Turn muting off.

•

Turn Advanced surround off if it causes distortion.

•

Switch off the unit, determine and correct the causes, then switch the unit on.

Causes include:

– Shorting (bare wires touching) of positive and negative speaker wires.

– Using speakers with an impedance lower than that rated for this unit.

– Straining of the speakers through excessive volume or power.

– Using the unit in a hot environment without proper ventilation.

•

If you have connected this unit to other equipment through the OPTICAL OUT

terminal, ensure you have selected the correct settings for “Dolby Digital”, “DTS

Digital Surround” and “MPEG

” in the SETUP menus’ “Audio” tab.

Unit displays

The display is dark.

“DVD NO PLAY”

“DVD NO DISC”

“F61”

“DVD U11”

“ERROR”

“DVD HMM”

MM stands for a number.

•

Press [SHIFT]+[DIMMER] until the display returns to the original brightness.

•

You inserted a disc which the unit cannot play; insert one that can.

•

You inserted a blank DVD-RAM disc.

•

You haven’t inserted a disc; insert one.

•

You haven’t inserted the disc correctly; insert it correctly.

•

Check and correct the speaker cord connections.

If this does not fix the problem, there is a power supply problem. Consult the dealer.

•

Disc is dirty. Wipe it clean.

•

Incorrect operation performed. Read the instructions and try again.

•

Trouble may have occurred. The number following “H” depends on the status of the unit.

Reset procedure:

Press [f] to switch the unit to the standby mode and then back to ON. Alternatively, press

[f] to switch the unit to the standby mode, disconnect the AC mains lead, and then

reconnect it.

•

If the service numbers fail to clear, note the service number and contact a qualified

service person.

For Australia, N.Z., Saudi Arabia, Kuwait, the Middle East and Southeast Asia

Although the unit is on standby

mode, the display lights up and

changes continuously.

•

Turn off the demo function.

•

If you set the clock, demo function will be turned off automatically.

For Australia, N.Z., Saudi Arabia, Kuwait, the Middle East and Southeast Asia

Television displays

•

You are trying to display incompatible contents.

•

Go to “Video” tab in the SETUP menus, and select “Enable” in “Progressive Out

(Component)”.

•

Go to “Display” tab in the SETUP menus, and select “On” for “On-Screen Messages”.

•

Go to “Disc” tab in the SETUP menus, and select the preferred language for “Menus”.

–

12, 39

–

Except for Southeast Asia

For Australia, N.Z., Saudi Arabia, Kuwait, the Middle East and Southeast Asia

“Cannot display group xx, content xx.”

For Saudi Arabia, Kuwait, the Middle East

and

Southeast Asia

“The progressive out is set to

“Disable”.

No on-screen display.

The disc’s menu is displayed

in a different language.

RQT7502_36_37_new 3/16/04, 3:14 PM37

Panasonic SCPM39D Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCPM39D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info