•
Specifi cations
•
Frequently Asked Questions
TH-42PY70FA, TH-42PY70F TH-50PY70F
Power Source AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use 486 W 561 W
Standby condition 0.5 W
Display
panel
Aspect Ratio 16:9
Visible screen size
106 cm (diagonal) 127 cm (diagonal)
922 mm (W) × 518 mm (H) 1,106 mm (W) × 622 mm (H)
Number of pixels 2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]
Sound
Speaker 160 mm × 42 mm × 2 pcs, 8
Ω
Audio Output 20 W (10 W + 10 W), 10% THD
Headphones M3 (3.5 mm) stereo mini Jack × 1
PC signals
VGA, SVGA, XGA
SXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems /
Band name
PAL B, G, H, I, SECAM B, G, SECAM L / L’
VHF E2 - E12 VHF H1 - H2 (ITALY)
VHF A - H (ITALY) UHF E21 - E69
CATV (S01 - S05) CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10) CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2 VHF R3 - R5
VHF R6 - R12 UHF E21 - E69
PAL 525/60 Playback of NTSC tape from some PAL Video re cord ers (VCR)
M.NTSC Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only) Playback from NTSC Video recorders (VCR)
Aerial - Rear VHF / UHF
Operating Conditions
Temperature : 0 °C - 35 °C
Humidity : 20 % - 80 % RH (non-condensing)
Connection Terminals
AV1 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
AV2 (Scart terminal) 21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV3
VIDEO RCA PIN Type × 1 1.0 V[p-p] (75
Ω
)
S-VIDEO Mini DIN 4-pin Y:1.0 V[p-p] (75
Ω
) C:0.286 V[p-p] (75
Ω
)
AUDIO L - R
RCA PIN Type × 2 0.5 V[rms]
COMPONENT
VIDEO
Y 1.0 V[p-p] (including synchronization)
PB, PR ±0.35 V[p-p]
AUDIO L - R
RCA PIN Type × 2 0.5 V[rms]
Others
HDMI1 / 2 TYPE A Connectors
•
This TV supports “HDAVI Control 2” function.
PC
HIGH-DENSITY D-SUB 15PIN R,G,B/0.7 V[p-p] (75
Ω
)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
Card slot SD CARD slot × 1
Output
AUDIO L - R
RCA PIN Type × 2 0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
1,134 mm × 688 mm × 330 mm (With Pedestal)
1,134 mm × 641 mm × 116 mm (TV only)
1,323 mm × 802 mm × 369 mm (With Pedestal)
1,323 mm × 754 mm × 99.5 mm (TV only)
Mass
42.0 k Net (With Pedestal)
35.0 k Net (TV only)
50.5 k Net (With Pedestal)
43.0 k Net (TV only)
Problem Actions
Screen Sound HDMI Other
Whirling sound is heard
•
The sound is from built-in cooling fan
(not a sign of faulty operation).
An error message appears
•
Follow the message’s instructions.
•
If the problem persists, contact the authorized Service Centre.
No image can be
displayed
•
Is “Colour” or “Contrast” in the Picture Menu set to the minimum?
(p. 22)
•
Check Colour system. (p. 25)
Blurry or distorted image
(no sound or low volume)
•
Reset channels. (p. 24)
No sound is produced
•
Is “Sound mute” active? (p. 9)
•
Is the volume set to the minimum?
Sound level is low
or sound is distorted
•
Sound signal reception may be deteriorated.
•
Set “MPX” (p. 22) in the Sound Menu to “Mono”.
•
Check Sound system. (p. 25)
Sound is unusual
•
Set the sound setting of the connected equipment to
“2ch L.PCM”.
•
Check the “HDMI1 Input” setting in the Sound Menu. (p. 22)
•
If digital sound connection has a problem, select analogue
sound connection. (p. 33)
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
•
Is the HDMI cable connected properly? (p. 36)
•
Turn Off the TV and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 40)
•
Use an equipment compliant with EIA/CEA-861/861B.
Unusual image is displayed
•
Turn off the TV with Mains power On / Off switch, then turn it on
again.
TV goes into
“Standby mode”
•
Off Timer function is activated.
•
The TV enters “Standby mode” about 30 min. after broadcasting
ends.
The remote control
does not work
•
Are the batteries installed correctly? (p. 6)
•
Has the TV been switched On?
Chaotic image, noisy
•
Set “P-NR” in the Picture Menu (to remove noise). (p. 22)
•
Check nearby electrical products
(car, motorcycle, fl uorescent lamp).
FAQs Specifi cations
Note
•
Design and Specifi cations are subject to change without notice. Weight and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
