Bedienungsanleitung Panasonic TH42BT300ER (Seite 27 von 76) (Englisch)

602459

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Adjusting Pos. /Size

● Auto Setup

When inputting a PC signal as an example, “H-Pos/V-Pos”, “H-Size/V-Size”, “Dot Clock” and

“Clock Phase” are automatically corrected.

This setting is enabled under the following conditions:

• This setting is not activated during Digital Zoom.

•

When inputting an analog signal (Component/PC):

This setting is enabled if “Component/RGB-in select” (see page 40) in Setup menu is “RGB”.

• When inputting a digital signal (HDMI/DVI):

A PC format signal enables this setting.

When the signal is not PC format, this setting is enabled only if “Over Scan” (see page 28) is

“Off” or “1:1 Pixel Mode” (see page 28) is “On”. “H-Size/V-Size” is not automatically adjusted.

This setting will be invalid and will not work under the following conditions:

• When VIDEO signal input

• Aspect is set to “Just”

• “Display size” in the Options menu (see page 60) is set to “On”

Using Remote Control

When on the remote control is pressed, “Auto Setup” will be executed.

When Auto Setup does not work, “Invalid” is displayed.

Auto mode

When the “Auto Setup“ is set to “Auto” in the Options menu (see page 61), automatic position

adjustment starts:

• When the display power is turned ON.

• When the input signal is switched.

● H-Pos

Adjust the horizontal position.

● V-Pos

Adjust the vertical position.

● H-Size

Adjust the horizontal size.

● V-Size

Adjust the vertical size.

● Dot Clock

(During Component/PC input signal)

Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this

happens, adjust so that any such noise is minimized.

● Clock Phase

(During Component/PC input signal)

Eliminate the ﬂ ickering and distortion.

Notes:

• If the dot clock frequency of an analog signal is 162 MHz or higher, “Dot Clock” and “Clock

Phase” cannot be automatically corrected.

• When digital signal input, Dot Clock and Clock Phase cannot be made.

• Auto Setup may not work when a cropped or dark image is input. In such case, switch to

a bright image with borders and other objects are clearly shown, and then try auto setup

again.

• Depending on the signal, out of alignment may occur after Auto Setup. Carry out ﬁ ne tuning

for the position/size as required.

• If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz,

1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in “XGA Mode”

(see page 45) may results in correct Auto Setup.

• Auto Setup does not work well when a signal such as additional information is superimposed

out of valid image period or intervals between synchronizing and image signals are short, or

for image signal with tri-level synchronizing signal added.

• If Auto Setup cannot adjust correctly, select “Normalise” once and press OK button, then

adjust Pos. /Size manually.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic TH42BT300ER Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic TH42BT300ER

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info