Bedienungsanleitung Panasonic TH42PH20ER (Seite 23 von 55) (Englisch)

602615

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

Adjusting POS. /SIZE

H-Pos Adjust the horizontal position. V-Pos Adjust the vertical position.

H-Size Adjust the horizontal size. V-Size Adjust the vertical size.

Dot Clock (During Component, RGB and PC input signal)

Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens,

adjust so that any such noise is minimized.

Clock

Phase

(During Component, RGB and PC input signal)

Eliminate the ﬂ ickering and distortion.

Clamp

Position

(During Component and RGB input signal)

Adjusts the clamp position when black parts of the image have no detail due to underexposure or are

tinged with green.

Optimum value for Clamp Position adjustment

When black parts have no detail due to underexposure (blackout)

→ Value that causes least blackout is the optimum.

When black parts are tinged with green

→ Value that cancels the greenishness without causing blackout is the optimum.

Over scan Turn image over scan On/Off.

Conﬁ gurable signals are as follows:

525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/60p,

1125/50p, 1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)

On Off

Notes:

• When “Off” is set, “H-Size” and “V-Size” cannot be adjusted.

• When the “Display size” is set to “On” in the Options menu, this setting will be invalid. (see page 44)

Notes:

• If the dot clock frequency is 108 MHz or higher, Dot Clock and Clock Phase cannot be made.

• When digital RGB signal input, Dot Clock and Clock Phase cannot be made.

• Auto Setup may not work when a cropped or dark image is input. In such case, switch to a bright

image with borders and other objects are clearly shown, and then try auto setup again.

• Depending on the signal, out of alignment may occur after Auto Setup. Carry out ﬁ ne tuning for the

position/size as required.

• If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024×768@60Hz,

1280×768@60Hz, and 1366×768@60Hz), pre-selecting the individual signal in “XGA Mode” (see

page 40) may results in correct Auto Setup.

• Auto Setup does not work well when a signal such as additional information is superimposed out

of valid image period or intervals between synchronizing and image signals are short, or for image

signal with tri-level synchronizing signal added.

• If Auto Setup cannot adjust correctly, select “Normalise” once and press ACTION (

), then adjust

Pos. /Size manually.

While the Pos. / Size display is active, if either the N button on the remote control is pressed at any time or the ACTION

( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.

Helpful Hint ( /

Normalise

Normalisation)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic TH42PH20ER Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic TH42PH20ER

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info