Bedienungsanleitung Panasonic tx pf46s10 (Seite 62 von 64) (Englisch)

144516

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Problem Actions

Screen

Chaotic image, noisy

Set “P-NR” in the Picture Menu (to remove noise). (p. 26)●

Check nearby electrical products●

(car, motorcycle, fluorescent lamp).

No image can be displayed

Is “Colour” or “Contrast” in the Picture Menu set to the minimum? ●

(p. 26)

Blurry or distorted image

(no sound or low volume)

Reset channels. (p. 30 and p. 31)●

Unusual image is displayed

Turn the TV Off with Mains power On / Off switch, then turn it On ●

again.

If the problem persists, perform “Shipping Condition” (p. 38).●

Sound

No sound is produced

Is “Sound mute” active? (p. 9)●

Is the volume set to the minimum?●

Sound level is low

or sound is distorted

Sound signal reception may be deteriorated.●

Set “MPX” (p. 27) in the Sound Menu to “Off”.●

(Analogue only)

Digital Channel

Due to the digital reception technologies involved, quality of the digital signals may be relatively low in ●

some cases, despite good reception of analogue channels.

Interference or

frozen / disappearing image in

DVB mode

Check “Signal Condition” (p. 32).●

If “Signal Quality” or “Signal Strength” are displayed in red, the

signal is weak.

Check aerial or cable. If problem persists, consult your local dealer.

●

Weather conditions will affect signal reception (heavy rain, snow,

●

etc.), in particular in poor reception areas. Even during good weather

the high pressure can cause poor reception of some channels.

Turn the TV off with the Mains power On / Off switch, then turn it On ●

again.

Some channels

cannot be tuned

Check the aerial or cable.●

Consult your local dealer.●

HDMI

Sound is unusual

Set the sound setting of the connected equipment to ●

“2ch L.PCM”.

Check the “HDMI1 / 3 Input” setting in the Sound Menu. (p. 27)

●

If digital sound connection has a problem, select analogue sound ●

connection. (p. 59)

Pictures from external

equipment are unusual

when the equipment is

connected via HDMI

Check the HDMI cable is connected properly. (p. 54)●

Turn the TV and equipment Off, then turn them On again.●

Check an input signal from the equipment. (p. 60)●

Use an equipment compliant with EIA/CEA-861/861B.●

Other

The TV does not switch On

Check the mains lead is plugged into the socket outlet.●

The TV goes into

“Standby mode”

Off Timer function is activated.●

The TV enters “Standby mode” about 30 mins. after analogue ●

broadcasting ends.

The remote control does not work

or is intermittent

Are the batteries installed correctly? (p. 6)●

Has the TV been switched On?●

The batteries may be running low. Replace them.●

Point the remote control directly at the front of the TV (within a ●

30 degree angle of the front of the TV).

Situate the TV away from sunshine or other sources of bright light

●

not to shine on the TV’s remote control signal receiver.

An error message appears

Follow the message’s instructions.●

If the problem persists, contact the authorized Service Centre.●

FAQs

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic tx pf46s10 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info