Bedienungsanleitung Panasonic U-16MX4 (Seite 6 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

672270

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Operation manual

U-5~18MX4 + U-8~16ME4

✽

M + U-8~16ME4 + U-4~6ML5

Urban Multi air conditioner

4PW40727-1A

Explanation of heating operation

It may take longer to reach the set temperature for general heating

operation than for cooling operation.

The following operation is performed in order to prevent the heating

capacity from dropping or cold air from blowing.

Defrost operation

■

In heating operation, freezing of the outdoor unit coil increases.

Heating capability decreases and the system goes into defrost

operation.

■

The indoor unit fan stops and the remote controller displays

■ After maximum 10 minutes of defrost operation, the system

returns to heating operation again.

Hot start

■ In order to prevent cold air from blowing out of an indoor unit at

the start of heating operation, the indoor fan is automatically

stopped. The display of the remote controller shows .

It may take some time before the fan starts. This is not a

malfunction.

7.2. Program dry operation

■ The function of this program is to decrease the humidity in your

room with minimal temperature decrease (minimal room

cooling).

■ The micro computer automatically determines temperature and

fan speed (cannot be set by the remote controller).

■ The system does not go into operation if the room temperature

is low (<20°C).

For systems without cool/heat changeover remote control

switch (See ﬁgure 5)

1 Press the operation mode selector button several times and

select (program dry operation).

2 Press the on/off button.

The operation lamp lights up and the system starts operation.

3 Press the air ﬂow direction adjust button. (Only for Double-ﬂow,

Multi-ﬂow, Corner, Ceiling-suspended and Wall-mounted.) Refer

to "7.3. Adjusting the air ﬂow direction" on page 4 for details.

Stopping the system

4 Press the on/off button once again.

The operation lamp goes off and the system stops operation.

For systems with cool/heat changeover remote control switch

(See ﬁgure 6)

1 Select cooling operation mode with the cool/heat changeover

remote control switch.

2 Press the operation mode selector button several times and

select (program dry operation).

3 Press the on/off button.

The operation lamp lights up and the system starts operation.

4 Press the air ﬂow direction adjust button. (Only for Double-ﬂow,

Multi-ﬂow, Corner, Ceiling-suspended and Wall-mounted.) Refer

to "7.3. Adjusting the air ﬂow direction" on page 4 for details.

Stopping the system

5 Press the on/off button once again.

The operation lamp goes off and the system stops operation.

7.3. Adjusting the air ﬂow direction

Refer to the operation manual of the remote controller.

Movement of the air ﬂow ﬂap (See ﬁgure 8)

For the following conditions, a micro computer controls the air ﬂow

direction which may be different from the display.

The air ﬂow direction can be adjusted in one of the following ways.

■ The air ﬂow ﬂap itself adjusts its position.

■ The air ﬂow direction can be ﬁxed by the user.

■ Automatic " " and desired position " ".

NOTE

■ The heating capacity drops when the outside

temperature falls. If this happens, use another

heating device together with the unit. (When using

together with appliances that produce open ﬁre,

ventilate the room constantly.)

Do not place appliances that produce open ﬁre in

places exposed to the air ﬂow from the unit or

under the unit.

■ It takes some time to heat up the room from the

time the unit is started since the unit uses a hot-air

circulating system to heat the entire room.

■ If the hot air rises to the ceiling, leaving the area

above the ﬂoor cold, we recommend that you use

the circulator (the indoor fan for circulating air).

Contact your dealer for details.

NOTE

Do not turn off power immediately after the unit stops,

but wait for at least 5 minutes.

NOTE

Do not turn off power immediately after the unit stops,

but wait for at least 5 minutes.

A Double-ﬂow + Multi-ﬂow units

B Corner units

C Ceiling-suspended units

D Wall-mounted units

COOLING HEATING

•When the room temperature is lower than

the set temperature.

•When starting operation.

•When the room temperature is higher than

the set temperature.

• At defrost operation.

•When operating continuously at horizontal air ﬂow direction.

•When continuous operation with downward air ﬂow is performed at the time of cooling with a

ceiling-suspended or a wall-mounted unit, the microcomputer may control the ﬂow direction,

and then the remote control indication also will change.

NOTE

■ The movable limit of the ﬂap is changeable.

Contact your dealer for details. (Only for Double-

ﬂow, Multi-ﬂow, Corner, Ceiling-suspended and

Wall-mounted.)

■ Avoid operating in the horizontal direction

"". It may cause dew or dust to settle on the

ceiling.

4PW40727-1A Page 4 Thursday, October 11, 2007 11:02 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic U-16MX4 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info