Bedienungsanleitung Panasonic WV-SC384 (Seite 86 von 244) (Englisch)

550986

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

“8192kbps *” is available only when the image capture size is “1280x960” or “1280x720”.

“128kbps *” is available only when the image capture size is “QVGA”, “VGA”, “800x600”

or “320x180”,

“640x360”.

“64kbps” is available only when the image capture size is “QVGA”, “VGA” or “320x180”, “640x360”.

“Unlimited*” is available only when “Frame rate” is selected for “Transmission priority”.

Note

• When “8192kbps *” or “Unlimited*” is selected, the number of users who can access H.264 images will

be limited to “1”. (Only a single user can access H.264 images.)

• The H.264 bit rate is limited by “Bandwidth control(bit rate)” on the [Network] tab of “Network” page

(®page 166). For this reason, the bit rate may be lower than the value when any value with an asterisk

(*) on the right is selected.

• It is impossible to select “Unlimited*” for both “H.264(1)” and “H.264(2)”.

[Image quality]

Select the image quality of H.264 images from the following.

Low(Motion priority)/ Normal/ Fine(Image quality priority)

• Default: Normal

Note

• When “Constant bit rate” or “Best effort” is selected for “Transmission priority”, this setting is available.

[Refresh interval]

Select an interval (I-frame interval; 0.2 - 5 seconds) to refresh the displayed H.264 images.

If using under a network environment with frequent error occurrences, shorten the refresh interval for H.264

to diminish image distortions. However, the refresh interval may be longer than the set value.

0.2s/ 0.25s/ 0.33s/ 0.5s/ 1s/ 2s/ 3s/ 4s/ 5s

• Default: 1s

[Transmission type]

Select the transmission type of H.264 images from the following.

• Unicast port (AUTO): Up to 14 users can access a single camera concurrently. “Unicast port1(Image)”

and “Unicast port2(Audio)” will automatically be selected when transmitting images and audio from the

camera. When it is unnecessary to fix the port number for H.264 image transmission such as when using

in a particular LAN environment, it is recommended to select “Unicast port (AUTO)”.

• Unicast port (MANUAL): Up to 14 users can access a single camera concurrently. It is necessary to select

“Unicast port1(Image)” and “Unicast port2(Audio)” manually to transmit images and audio from the camera.

It is possible to fix the port number of the router used for H.264 image transmission via the Internet by

setting “Unicast port (MANUAL)” (®page 166). Refer to the operating instructions of the router in use.

• Multicast: Unlimited number of users can access a single camera concurrently. Complete the entry field

of “Multicast address”, “Multicast port” and “Multicast TTL/HOPLimit” when transmitting H.264 images with

multicast.

* Refer to page 9 for further information about the maximum concurrent access number.

• Default: Unicast port (AUTO)

[Unicast port1(Image)]

Enter the unicast port number (used to transmit images from the camera).

• Available port number: 1024 - 50000 (Only even numbers are available.)

• Default:

– H.264(1): 32004

– H.264(2): 32014

86 Operating Instructions

11 Configure the settings relating to images and audio [Image/Audio]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic WV-SC384 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic WV-SC384

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info