Bedienungsanleitung Panasonic WV-SC384 (Seite 125 von 244) (Englisch)

550986

125

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

– when the target moves too fast or too slow

– when the camera is shaking

• In no event shall Panasonic System Networks Co., Ltd. be liable to any consequential inconvenience,

or loss or damage, arising out of the settings or results of the Auto tracking system or face detection.

• We recommend that you use this setting under the following setting conditions to improve the detection

accuracy.

– set the size of the tracking target to over 1/5 of the monitoring screen (lengthwise)

– set the tilt angle within 20°-55° (®page 96)

Procedure to setup auto track cooperation

If 2 or more SW396/SC386 cameras are used, tracking of targets can be coordinated between cameras. (Auto

track cooperation setting)

For example, the procedure for getting Camera 2 (IP address: 192.168.0.12) to take over auto tracking from

Camera 1 (192.168.0.11) when the tracking target enters into alarm area No.1 during auto tracking as shown

below, is explained here.

Camera 1

IP address: 192.168.0.11

Camera 2

IP address: 192.168.0.12

Panasonic alarm protocol notification is sent

During auto tracking,

Camera 1 checks for targets

in alarm area No. 1

Camera 2 moves to

the set preset position

and starts auto tracking

Alarm area No. 1

[2]

[3][1]

1. Set an alarm area to Camera 1 in the area where you want to perform auto track cooperation.

Display the “Auto track setting” page.

With “Auto track alarm” select “On(In preset alarm area)” and click the “Set” button.

Select 1 from the “Area No.” pull-down menu in the alarm area.

While monitoring images, perform the pan/tilt/zoom, and then set the alarm area.

Click the “Set” button.

2. On Camera 2, configure the preset position for received notification commands. (Configure the preset

position so that alarm area No. 1 enters the screen as performed in step 1.)

Display the “Preset position” setting page. (®page 113)

Select a preset number that you want set from the “Preset” pull-down menu.

While monitoring images, perform the pan/tilt/zoom, and then set the preset position.

Click the “Set” button.

3. Set Camera 1 (IP address: 192.168.0.11) to notify commands.

Display the “Notification” screen from the “Alarm” page. (®page 148)

From “Panasonic alarm protocol”, set “Panasonic alarm protocol” to “On” and click the “Set” button.

From “Destination of notification”, check the “Alarm” checkbox of “Address 1” (any notification

destination address can be selected), and enter 192.168.0.12 in “Destination IP address”.

Set “Auto track cooperation” to “On”, and select “1” for the alarm area number.

Operating Instructions 125

11 Configure the settings relating to images and audio [Image/Audio]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic WV-SC384 Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic WV-SC384

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info