Bedienungsanleitung Paradigm SA-10R (Seite 8 von 24) (Englisch, Französisch)

568775

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

. Connecting and Installing (continued)

Installing

b) Holding the speaker’s front lip with your thumbs and index fingers, push the mounting screws toward

each other with your other fingers so that the brackets fit through the hole. Release the screws and

gently push the speaker to the wall/ceiling. (Fig. 5a)

While holding the speaker in place, alternately tighten each screw until the speaker is firmly installed.

(Fig. 5b)

Round

and Square Speakers

With grille removed and bracket attached to speaker, place complete assembly to the wall or ceiling and …

Connecting

(except models with ‘SM’ in their name, see connection instructions farther below):

a) Connect speaker cable as outlined on page 6, Fig. 8a, in section on Rectangular Speakers.

Installing

b) For Speakers With Two Mounting Screws: Holding the speaker flange with your fingers, push on

the screw heads with your thumbs to extend rear bracket. The bracket is oblong, extending past

each screw. Fit one oblong end into the hole far enough to allow the other oblong end to also fit

into the hole. (Fig. 6a)

For Speakers With Four

Mounting Screws: Holding the speaker’s front lip with your thumbs and

index fingers, push the mounting screws toward each other with your other fingers, so the mounting

brackets can fit through the hole with an “up-and-in” motion. Release the screws and gently push the

speaker to the ceiling/wall. (Fig. 7a)

Models with Guided Soundfield

™

: Rotate the speaker so that the drive assembly points in desired

direction (not shown).

c) While holding the speaker in place, alternately tighten each screw until the speaker is firmly

installed. (Figs. 6b and 7b)

Connecting ‘SM’ Models

Stereo Input

(Single Speaker) (Fig.8b): Connect one speaker channel at a time to your receiver/amplifier.

Connect the Right red (+) amplifier terminal to the Right red (+) speaker terminal and the Right black (-)

amplifier terminal to the Right black (-) speaker terminal. Connect the Left red (+) amplifier terminal to

the Left red (+) speaker terminal and the Left black (-) amplifier terminal to the Left black (-)

speaker terminal.

Follow the installation instructions provided earlier.

Mono Input

(Fig. 8c): Connect one speaker at a time to the left and right channels of your

receiver/amplifier. First, convert the Right speaker to Mono: Using a short piece of cable, connect the

Right red (+) speaker terminal to the Left red (+) speaker terminal and the Right black (-) speaker terminal

to the Left black (-) amplifier terminal. Then …

Connect the Right red (+) amplifier terminal to the Right red (+) speaker terminal and the Right black (-)

amplifier terminal to the Right black (-) speaker terminal.

Repeat entire procedure for Left speaker, then follow installation instructions provided earlier.

3. Installing the Grille

Press the grille into the groove on the front face of the speaker (not shown). Magnets hold the grille in

place (in-ceiling models only).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Paradigm SA-10R Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info