Bedienungsanleitung Paradigm UltraCube 10 (Seite 7 von 20) (Französisch)

568673

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

When using two subwoofers, placing one in the front of the room and the

other in the rear of the room (as shown in Fig. 2) usually provides the best

bass performance and sonic integration. Consult the ﬁne tuning section of

the Owner’s Manual for more information on adjusting phase settings. If

those locations are not possible or if you want to experiment with placement

options using two subwoofers, the following procedure will be a helpful guide

to achieving better bass performance. Refer to “Subwoofer Connection” then

proceed as follows:

1. Temporarily turn all speakers off (either by turning your ampliﬁer off or

disconnecting them);

2. Connect and place one subwoofer in the central area of your listening room.

Follow directions for connection, as outlined in the following section;

3. At a moderately loud level, play music or a video soundtrack with

extended bass that is repetitive or continuous;

4. Walk around your room and note where the bass sounds louder and

where it sounds quieter;

5. Place the ﬁrst subwoofer within a louder bass area of your room; then

place the second subwoofer within a quieter bass area of your room;

6. Connect both subwoofers and switch all speakers back on; and switch

the ampliﬁer on, or reconnect it;

7. Follow “Fine Tuning” instructions on page 8, to optimize your system’s

overall bass performance.

PLACING TWO SUBWOOFERS IN YOUR LISTENING ROOM

NOTE: The preceding is only a guideline. You may want to use a

bass test disc and SPL meter to more accurately determine the bass

characteristics of your listening room (see Dealer for more information).

Remember that room acoustics vary so it may take some experimenting

with placement to achieve the best subwoofer performance.

subwOOfer CONNeCTiON

SAFETY PRECAUTION: Before proceeding with this

section be sure to read and follow all safety precaution

and instruction notices at the beginning of this manual.

Turn all components OFF before

connecting the subwoofer.

We recommend the use of high-quality cables and connectors when

hooking up your subwoofer (see Dealer).

IMPORTANT: It is important that you become familiar with your powered

subwoofer’s Input/Output Facilities and Control Facilities. Before connecting

your subwoofer, read the following sections.

Facilities vary by model. Inspect your subwoofer’s rear panel and check

mark the facilities that apply to your model.

INPUT/OUTPUT FACILITIES

q Line-Level Input

Allows connection from the Sub/LFE Output of an A/V receiver,

processor, Paradigm

X-Series subwoofer control unit (optional) or other

suitable low-level source.

q

Speaker-Level Input

Allows easy connection from the speaker output terminals of an

ampliﬁer or receiver or from the front speakers’ hook-up terminals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Paradigm UltraCube 10 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info