Bedienungsanleitung Parkside IAN 109803 PDBS 6.2 A1 (Seite 12 von 39) (Deutsch, Englisch, Holländisch)

745457

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

12 GB/IE

Cleaning and storage / Information about warranty and service processing

Start-up / After initial use / Cleaning and storage

Cutting

Activate the trigger

to start using the shears.

Move the metal shears toward the item you wish

to work on. If possible, already run the shears

at full speed when applying them.

Note: The shears may take up to 8 seconds to

be fully ready for use and reach full force. Dur-

ng this time you should wait before applying th

shears to ensure better cutting results and treat

the device with care.

Note: Do not apply too much pressure whilst

cutting. Do not overburden the shears. In additio

to possible unclean cutting results, this could also

cause metal slivers to chip oﬀ and ﬂy about.

Note: Metal slivers ﬂying about can be very

dangerous!

Note: If the compressed air supply is tempo-

rarily cut oﬀ due to power failure or temporary

compressor failure, immediately release the trig-

ger

. If you now wish to continue working,

you must ﬁrst remove the metal shears all the

way out of the work piece. You can then con-

tinue working.

When using the device always be aware of the

following items:

The shears must always operate at full speed.

This means, the compressor must always supply

suﬃcient pressure and air volume.

- Work slow. Slowly guide the shears along the

work piece and work without applying exces-

sive pressure.

- Move the shears smoothly.

- Do not tilt the shears.

Please tighten the screws of the cutter head re-

gularly and replace worn or damaged cutting

edges if necessary (see Fig. E).

Use the corresponding Allen key when doing this.

Check the cutter head after 2 minutes of conti-

nuous operation to ensure it is securely seated.

After initial use

Once the task has been ﬁnished the equipment must

be disconnect from the compressed air supply.

This ﬁrst requires the pressure to be completely re-

leased from the lines.

Switch oﬀ the compressor.

To release potentially remainders of compressed

air, brieﬂy activate the trigger

of the device.

Pull back the lock.

Take oﬀ the coupler.

Spare parts / replacing

consumables

When replacing items, always be sure the com-

pressed air supply is disconnected!

ote: The shear head does not necessarily ha

to be removed all the way. After loosening the

screws you can remove the parts of the cutter

blades to replace the defective part.

Use a ﬁtting hex wrench to loosen the screws on

the underside of the shear head (see Fig. E). Re-

move the blades and replace the defective part.

During assembly be sure the blades are corre

ctly

aligned.

First insert the lower blade.

Then insert the centre piece.

Then insert the marked ring. This is merely a spacer

between the upper and lower blade.

Now insert the upper blade and secure the shear

head with the screws.

Note: please note, the notches on the blades

must face the inside.

Cleaning and storage

To ensure a long life and trouble-free operation, it‘s

important to observe the following instructions.

Always disconnect the tool from the compressed

air source before cleaning it.

Clean your tool with a soft, dry cloth or lightly

blow it out with compressed air. Never use

caustic cleaners.

109803_par_Druckluft-Blechschere PDBS 6.2A1_content_NL.indd 12 09.04.15 16:09

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 109803 PDBS 6.2 A1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 109803 PDBS 6.2 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info