Bedienungsanleitung Parkside IAN 109910 PDFP 500 B2 (Seite 32 von 36) (Französisch, Italienisch)

745455

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

32 GB

Initial use / Maintenance and CleaningSafety advice / Initial use

Wear additional personal protective

equipment such as appropriate protec-

tive gloves and protective masks or

respirators when spraying or handling

chemicals. The wearing of protective equipment

in such conditions reduces exposure to harmful

substances.

Do not spray on yourself, other people

or animals. Keep hands and other body

parts away from the spray jet. If the

spray penetrates the skin, seek medical help

immediately. The material being sprayed can

even penetrate the skin through a glove and be

injected into your body.

Do not treat an injection as a simple cut.

A high pressure jet may inject toxins

into the body and cause serious inju

ries.

If the spray is injected into the skin, seek medical

help immediately.

Pay attention to any possible dangers

of the material being sprayed. Note

the markings on the container or the

manufacturer’s information relating to

the material being sprayed, including

the instruction to use personal protec-

tive equipment. The manufacturer’s in-struc-

tions must be followed to reduce the risk of ﬁre, as

well as injuries caused by toxins, carcinogens, etc.

Never spray without the nozzle head

in place. The use of a special nozzle insert

with the appropriate nozzle head reduces the

probability of a high-pressure jet penetrating the

skin and injecting toxins into the body.

Initial use

HVLP properties

This device uses an HVLP system (High Volume Low

Pressure). It ensures the increased application of

(paint) materials with lower consumption.

Important: Do not exceed the maximum working

pressure of 3 bar.

Connecting the device

Operate the product only with cleaned, con-

densate- and oil-free compressed air and never

exceed the maximum working air pressure at

the device of 3 bar.

The compressed air source must be ﬁtted with a

(ﬁlter) / pressure reducer so that the air pressure

can be regulated.

In order to operate this device you require a ﬂexible

compressed air hose with quick-release coupling

and an appropriate source of compressed air.

Observe the operating and safety instructions of the

compressed air source and any special instructions

concerning paint preparation.

Note: Ensure the correct working pressure. An ex-

cessive working pressure leads to increased ﬁne

dispersion and results in too rapid evaporation of

the liquid. The surfaces become rough and develop

poor adhesion properties. If the working pressure is

too low on the other hand, the paint material is not

suﬃciently atomised. Undulating surfaces and the

formation of drops are the result.

Connect the compressed air hose with the

rapid-release coupling to the compressed air

connection

of the device. This automatically

locks into place.

Use the ﬁlter pressure reducer of the compressed

air source to set the working pressure to 3 bar.

Preparing the spraying surface

Mask oﬀ the surroundings of the spraying surface

thoroughly over a wide area. Otherwise all

non-covered areas or surfaces may become soiled.

Make sure that the spraying surface is clean,

dry

and free of grease.

Roughen smooth surfaces and then remove the

sanding dust.

Turning the device On / Oﬀ

Working Instructions:

- Insert the ﬁlter in the gun (see Fig. C).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 109910 PDFP 500 B2 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 109910 PDFP 500 B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info