Bedienungsanleitung Parkside IAN 113362 PMGS 12 C3 (Seite 13 von 91) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch)

745224

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

13 GB/IE

General safety advice for electrical power tools / Operation

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid abrading paints containing lead

or other substances hazardous to

health.

Do not machine materials containing

asbestos. Asbestos is a known carcinogen.

Do not machine moist materials or

damp surfaces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

Switch the device off

and allow it to come to a standstill be-

fore you put it down.

Always keep the de

vice

clean, dry and free of oil or grease.

This device is not intended to be used by per-

sons (including children) with impaired physi-

cal, sensory or mental capacity or lacking the

experience and / or knowledge. Always super-

vise children to ensure they do not play with

the tool.

If the external connection wire / cable(s)

for this transformer is / are damaged, it / they

must be replaced by the manufacturer or its cus-

tomer service, or a similarly qualiﬁed person to

avoid hazards.

Safety isolating transformer

fail-safe

Fusible cut-out

Operation

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories. The use

of tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Changing the battery

ATTENTION!

Do not leave drained battery in the device, as

even leak-proof batteries can corrode, releasing

chemicals which could be harmful to your health

or ruin the device.

Do not leave batteries lying about carelessly.

Children or pets could swallow them. If acciden-

tally swallowed seek immediate medical attention

Remove the batteries from the device when it

will not be used for extended periods to prevent

leaks.

Touching leaked or damaged batteries may

cause chemical burns. Therefore wear suitable

protective gloves in this event.

Ensure batteries are not short-circuited. Never

throw batteries into ﬁre.

Do not recharge batteries. Explosion hazard!

Ensure the LED light is switched oﬀ. Remove the

three battery cover screws at the back of the

grip collar with LED

Remove the drained battery and replace with a

new battery (button cell LR41). Please note the

correct polarity when inserting the batteries.

Close the battery compartment by fastening the

three screws.

Inserting or replacing

a tool / collet

Press the spindle lock

and keep it pressed.

Rotate the clamping nut

until the lock

engages.

Loosen the clamping nut

with the combina-

tion key

If a tool is already inserted, remove it.

First insert the tool you wish to use through the

clamping nut

before you insert it into the

collet

suitable for the tool shaft.

Press the spindle lock

and keep it pressed.

Insert the collet

into the threaded insert and

tighten the clamping nut

on the thread using

the combination key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 113362 PMGS 12 C3 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info