Bedienungsanleitung Parkside IAN 270414 PTBM 500 B2 (Seite 9 von 76) (Deutsch, Englisch, Holländisch, Französisch)

745345

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

GB IE

CAUTION!

- The use of other bits and other accessories

can result in a risk of personal injury.

Have your power tool be repaired by a quali-

ed electrician

- This power tool complies with the relevant

safety regulations. Repairs may only be

performed by a qualied electrician,

using original spare parts; otherwise acci-

dents involving the user may result.

Service:

• Have your power tool repaired

only by qualied specialists and

only with original spare parts. This

will ensure that the power tool remains

safe.

Safety Instructions for

Box Column Drills

• Never make the warning labels

on the power tool illegible.

• Attach the power tool to a solid,

at and horizontal surface. If the

power tool can slip or wobble, the bit

may not be guided smoothly and safely.

• Keep the work area clean except

for the workpiece to be machined.

Sharp-edged drilling chips and objects

can cause injury. Material mixtures are

particularly dangerous. Light metal dust

can burn or explode.

• Set the correct speed before st-

arting work. The speed must be

appropriate for the drill diameter

and the material to be drilled. At

an incorrectly set speed the bit may get

jammed in the workpiece.

• Only when the device is turned on

should the bit be moved against

the work piece. Otherwise there is a

danger that the bit will get jammed in the

workpiece and the workpiece will rotate

with the bit. This can lead to injuries.

• Do not put your hands in the area

of the drill while the power tool is

running. Upon contact with the bit is a

risk of injury.

• Never remove drilling chips from

the drilling area while the power

tool is running. Always put the drive

mechanism in the standby position rst

and then turn on the power tool.

• Do not remove accumulated drill

chips with your bare hands. There is

a risk of injury due to hot and sharp metal

shavings in particular.

• Break up long drilling chips by

interrupting the drilling operation

with a short backward rotation of

the rotary wheel. Long drilling chips

may cause injury.

• Keep handles dry, clean and free

from oil and grease. Greasy, oily

handles are slippery and lead to loss of

control.

• Use clamps to hold the workpie-

ce in place. Do not work on any

workpieces that are too small for

clamping. If you hold the workpiece by

hand, you cannot hold it sufciently tightly

against rotation and may hurt yourself.

• Switch the power tool off imme-

diately if the bit jams. The bit jams

when:

- the power tool is overloaded or

- the workpiece to be machined is jam-

med.

• Do not touch the bit after working

before it has cooled down. The bit is

very hot during use.

• Inspect the cable regularly and

have a damaged cable repaired

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 270414 PTBM 500 B2 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info