745345
14
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
14
GB IE
Clamping the Workpieces
Only work with workpieces that can be
securely clamped. The workpiece must not
yield too much. Otherwise it is nor possib-
le to apply adequate tension.
The workpiece must not be too small or too
large either.
Removing Blockages
- You should always select a suitable
feed rate which allows trouble-free chip
breaking.
- If the bit is jammed in the workpiece,
turn off the power and unplug the po-
wer cord. Turn the bit on the drill chuck
anticlockwise with a little jerk to break
the chip and release the bit again.
- If a fragment is produced during the
processing of the workpiece, turn off
the power and unplug the power cord.
Use a pair of pliers and remove the
fragment to prevent it ying off in an
uncontrolled way.
Cleaning and Servicing
Pull the mains plug before any ad-
justments, maintenance or repair.
Have any work on the device
that is not described in this in-
struction guide performed by
a professional. Only use ori-
ginal parts. Allow the device
to cool off before any mainte-
nance or cleaning is underta-
ken. There is a risk of burning!
Always check the device before using it
for obvious defects such as loose, worn or
damaged parts, correct the positioning of
screws or other parts. Exchange the dama-
ged parts.
Cleaning
Do not use any cleaning agents or
solvents. Chemical substances can
etch the plastic parts of the device.
Never clean the device under run-
ning water.
Thoroughly clean the device after every
use.
Clean the ventilation openings and the
surface of the device with a soft brush
or cloth.
Remove chips, dust and dirt with a va-
cuum cleaner if necessary.
Lubricate moving parts regularly.
Do not allow lubricants to come into
contact with switches, V-belts, pulleys
and drill lifting arms.
Storage
Store the appliance in a dry place well
out of reach of children.
The device can be relocated over a
short distance with two people. Reloca-
ting the device over a longer distance
generally has to take place with a trans-
port aid.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 270414 PTBM 500 B2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info