Bedienungsanleitung Parkside IAN 270420 PHKSA 18 Li B2 (Seite 11 von 56) (Deutsch, Englisch, Holländisch, Dänisch)

745234

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

PHKSA 18-Li B2

♦ Insert the mains plug into the mains power socket.

The red control LED lights up.

♦ The green control LED

indicates that the

charging process is complete and the battery

pack is ready.

♦ Insert the battery pack

back into the appli-

ance.

■ Never recharge a battery pack

again

immediately after rapid charging. This could

overcharge the battery pack , thus reducing

the lifespan of the battery and charger .

♦ Switch oﬀ the charger for at least 15 minutes

between successive charging sessions. Also

disconnect the power plug from the mains

power socket.

Attaching/disconnecting the battery

pack to/from the appliance

Inserting the battery pack:

♦ Allow the battery pack to click into the

handle.

Removing the battery pack:

♦ Press the release button

and remove the

battery pack .

Checking the battery charge level

♦ Press the battery charge level button to

check the status of the battery (see also main

diagram). The status/remaining charge will be

shown on the battery display LED as follows:

♦ RED/ORANGE/GREEN = maximum charge/

power

RED/ORANGE = medium charge/power

RED = low charge – charge the battery

Checking the blade guard

♦ Pull back on the release lever for the blade

guard as far as the stop.

The blade guard

must move freely without jam-

ming and must spring back into its starting position

automatically when you let go of the release lever

for the blade guard .

Initial use

Fitting/changing the saw blade

Always remove the battery pack before changing

the saw blade !

1. Set the cutting depth (using the locking screw

)

to the minimum position, 0 mm.

2. Swing the blade guard

back using the

release lever and put the appliance down.

3. Press the spindle lock button (until it engages)

and use the Allen key to release the clamping

screw . Now remove the clamping screw

and the clamping ﬂange (see also Fig. A).

Fig. A Changing the saw blade

4. Remove

saw blade.

5. Fitting a saw blade

is carried out in the reverse

order.

6. Press the spindle lock button

(until it engages)

and use the Allen key to tighten the clamping

screw .

WARNING!

► The arrow on the saw blade

must corre-

spond to the arrow showing the direction

of rotation (running direction shown on the

appliance).

■ Ensure that the saw blade

is suitable for the

rotational speed of the tool.

Rip fence

♦ Loose the wing screw and insert the rip

fence into the rip fence slot .

♦ Set the desired cut width with the help of the

scale on the rip fence and the cut out in the

base plate

(see also Fig. B).

The right-hand recess in the base plate is for a

cutting angle of 0°. The left-hand recess in the

base plate is for a cutting angle of 45°.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 270420 PHKSA 18 Li B2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 270420 PHKSA 18 Li B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info