Bedienungsanleitung Parkside IAN 273460 PTK 2000 B2 (Seite 39 von 204) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

745555

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

GB IE

2 Maintenance and Servicing

– Always remove the mains plug

when carrying out any adjustments

or maintenance work.

 

by various factors, including the

properties of the blades, the con-

dition of the saw blade and power

tool. If possible, use saw blades

that are designed to reduce the

noise level, service the power tool

and tool attachments regularly and

repair them if necessary to reduce

noise.

- Report any faults to the power tool,

safety devices or the tool attach-

ment as soon as they are disco-

vered to the person responsible for

safety.

3 Safe Working

– Use the push stick or the handle

with push block to pass the workpi-

ece safely past the saw blade.

– Make sure that the riving knife

is always used and that this is

correctly adjusted.

– Use the upper blade guard and

adjust it correctly.

– Use only saw blades whose maxi-

mum speed is not lower than the

maximum spindle speed of the tool

being used and which are suitable

for the material to be cut.

– Do not create any rebates or

grooves unless a suitable protective

device, such as a tunnel guard, is

attached above the saw table.

– Circular saws must not be used for

slotting (cutting grooves which end

in the workpiece).

– When transporting the power

tool, use only the transport devices

supplied. Never use the guards for

handling or transporting the tool.

- During transport, make sure that

the top part of the saw blade is co-

vered, for example with the guard.

– Ensure that the only spacer

washers and spindle rings which

are used are suitable for the purpo-

se stated by the manufacturer.

 



particles such as chips and cutting

residues.

– Working position always to the

side of the saw blade.

– Do not remove any cutting residues

or other parts of the workpiece

from the cutting area for as long

as the machine is running and the

sawing unit is not yet in the rest

position.

– Secure long workpieces against

tilting at the end of the cutting

operation (e.g. unwinding stand or

roller stand).

– Caution! long workpieces against

tilting at the end of the cutting

operation (e.g. unwinding stand or

roller stand).

– Caution! Never remove any loose

splinters, chips or jammed pieces

of wood when the saw blade is

still running.

• Always switch off the machine and

remove the plug before repairing

any faults or removing jammed

pieces of wood.

• Always switch off the motor and

remove the plug before carrying

out any conversions or adjustment,

measurement and cleaning work.

• Before switching on, check that

the spanners and adjustment tools

have been removed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 273460 PTK 2000 B2 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info