Bedienungsanleitung Parkside IAN 275633 PABK 60 B2 (Seite 10 von 57) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

745468

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

10 GB/IE

… / Cleaning and care / Information about warranty and service processingPreparations for use

Preparations for use

Warning: This appliance can slide on smooth sur-

faces during normal use. This can be prevented by

applying light pressure to the appliance.

Clean dusty surfaces so that the suction cups can grip

well. Otherwise a slight shift in position is possible.

Connecting the airbrush set

Be absolutely certain to disconnect the mains

plug before connecting the airbrush set to the

compressor and release the pressure in the lines

by actuating the vent of the air blow gun

Use the respective screw connection to connect

the spray stylus

with the coiled hose

and

the coiled hose to the airbrush connection

Use the included open-end wrench.

(see Ill. A).

Fasten the paint mixing beaker with connection

lid

to the spray stylus

(see Ill. B).

Insert the mains plug into the mains socket.

Note: For optimal results, professionals connect

an intermediate pressure reducer (not included

with delivery). The pressure reducer can be used

to adjust the compressed air at the spray gun

and optimise it to your needs.

Mixing paints for use

The paints included are water-soluble. In order to

properly apply the paints, add water and stir. As

delivered, the paints are too viscous.

First ﬁll the beaker with your selected paint

colour with water.

Now screw the cover back on the beaker and

shake it.

Now remove two full droppers (1.5 mark on

the dropper) and ﬁll these into a mixed glass

ﬁlled half way with water.

Shake the beaker. Now your paint has reached

the correct consistency.

Attach the paint mixing glass

according

to Ill. B.

Note: If desired, you can adjust the amount of

water added to inﬂuence the colour intensity

yourself as with a watercolour box. The more

water you add, the „thinner“ the colour.

You can also mix individualised colour tones

from the available colour pastes. Please take

note, there must be no paint clumps remaining

in the paint containers. The consistency should

correspond to that of water.

Note: If the paint used does not cover well, in-

crease the amount of paint in the mixture ratio.

Turning airbrush compressor

on / oﬀ

Turn the airbrush compressor

on by setting the

on / oﬀ switch

to the position “I“ (see Ill. C).

Turn the airbrush compressor

oﬀ by setting

the on / oﬀ switch

in the position “0“ (see

Ill. C).

Note: Full pressure is built up after two seconds.

Regulating the air pressure

Regulate the air pressure by actuating the vent

of the air blow gun

to more or less of an

extent.

The air pressure can be adjusted by turning the

air pressure regulator

The air gauge shows the pressure level.

Turning the air pressure regulator

to the left

reduces the air pressure, turning the air pres-

sure regulator

to the right increases the air

pressure.

An internal valve bleeds overpressure if it is not

reduced.

Regulating the spraying results

Regulate the amount of the paint supplied by

turning the paint nozzle of the spray stylus to

the right or left (see Ill. B).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 275633 PABK 60 B2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info