Bedienungsanleitung Parkside IAN 275671 PDSS 310 A2 (Seite 7 von 69) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

745544

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

8 GB/IE

Safety instructions for air toolsSafety instructions for air tools

Unforeseen tool movements may result in ha-

zardous situations.

Crushing risk based on the torque between the

counter bearing and the work piece.

Keep hands away from the tool (socket) being

used to prevent the risk of injuries.

Only use holders and adapters in good condi-

tion and intended for use with the machines

described here.

Avoid an unnatural posture. Always maintain a

proper footing and balance. This will allow you

to better control the electrical power tool in un-

foreseen circumstances.

Switch the device oﬀ when not in use.

Always wear personal protective

equipment and safety glasses. Wea-

ring personal protective equipment

such as dust mask, non-slip safety shoes, hard

hat or ear protectors, depending on the type of

air tool and its application, reduces the risk of

injuries.

Protect hoses from kinks, constrictions, solvents

and sharp edges. Keep hoses away from heat,

oil and rotating parts.

Replace damaged hoses immediately. A dama-

ged supply line may result in the air hose ﬂap-

ping about, possibly resulting in injuries.

Do not use the equipment when fatigued or un-

der the inﬂuence of drugs, alcohol or medica

tions.

Just a moment of carelessness when using this

equipment may result in serious injuries.

Do not directly inhale exhaust air. Keep eyes

away from exhaust air. Exhaust air from the air

tool may contain water, oil, metal particles or

contaminants from inside the compressor. This

may result in health damage.

CAREFUL WHEN PUT-

TING THE TOOL DOWN! Always put down

the device so the trigger is not activated. This

could potentially result in accidental activation

of the tool, which again could result in hazards.

Only use suitable accessories. These can be

purchased from the manufacturer. Using non-

OEM accessories may result in hazards.

Only use ﬁltered and regulated compressed air.

Dust, caustic vapours and / or moisture may

damage the motor of an air tool.

The hose must be constructed for a

minimum pressure of 8.6 bar or

125 PSI, but no less than 150 % of

the maximum pressure produced by the system.

The tool and supply line must be

equipped with a hose coupling to

completely release pressure when

disconnecting the coupling hose.

DANGER! Avoid contact with live lines. This

device is not insulated against electric shock.

Do not modify this equipment in any way wit-

hout the manufacturer‘s approval.

Only use the tool at the speciﬁed pressure

(max. 6.3 bar).

Disconnect the tool from the air supply after

each use and when not in use.

Discontinue use if the tool is leaking or in need

of repair.

Never connect the tool to an air hose with

pressure exceeding 6.3 bar.

Keep your working area clean and well lit.

Untidy or poorly lit working areas can result in

accidents. Doing so will allow you better control

of the equipment, particularly in unforeseen cir-

cumstances.

Only have the equipment

repaired by qualiﬁed specialist personnel using

OEM spare parts. This will ensure your device

remains safe to use.

Keep children and other individuals away from

the equipment during use. Distractions can

cause you to lose control of the equipment.

Wear suitable clothing. Do not wear loose

clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts. Loose

clothing, jewellery or long hair can become

caught in moving parts.

Put down trigger and equipment in the event of

unexpected compressor failure.

Never use or store the tool in humid, dusty lo-

cations or near water, other ﬂuids or hazar-

dous gases.

If possible, use a condensate trap or regularly

drain condensate (water) from hoses and pipes

before and during air tool use.

Secure work pieces. Use clamps or a vice to

secure the work piece. Holding the work piece

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 275671 PDSS 310 A2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info