Bedienungsanleitung Parkside IAN 281392 PSH 3 A2 (Seite 17 von 68) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746415

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

18 GB/IE

… / Cleaning and ... / Environmental ... / Environmental ... / TroubleshootingSafety instructions / Initial use

Replace the protective visor if

scratches or damages appear.

The welding helmet does not pro-

vide protection against impact.

Frequent use, cleaning or storage

can mean that the service life is

less than 6 years. Replace the

welding helmet immediately if

the viewing panel gets scratched

or the viewing panel is visibly

damaged in any other way.

ATTENTION! Materials that

come into contact with the wearer‘s

skin

may cause allergic reactions in

peo

ple with sensitive skin.

ATTENTION! Eye protection

can represent a hazard for the

wearer if it is worn over normal cor-

rective glasses due to the impact

from high-speed particles.

ATTENTION! If protection

against high-speed particles at

extreme temperatures is required,

the eye protection chosen must be

labelled with the letter T directly af-

ter the letter for the impact intensity,

i. e. FT, BT or AT. If the letter for the

impact intensity is not followed by

the letter T, the eye protection may

only be used against high-speed

particles at room temperature.

Initial use

Note: Only use the welding helmet with the rear

pane mounted

Note: Keep the UV ﬁlter‘s sensors

clean and

clear.

Check that the welding helmet and the protective

screen are intact before each use. If the protective

screen has scratches, cracks or irregularities, it must

be replaced before use, as serious injuries may oc-

cur otherwise.

Remove the protective ﬁlm from the inside and

the outside of the visor.

Put on the welding helmet with the help of the

headband

. Press the adjustment buttons

to make the welding helmet tighter and the ad-

justment button

, to ﬁx the welding helmet.

When adjusting, ensure that your head is placed

as far into the helmet as possible and that it sits

as close as possible to your face.

Set the appropriate darkening shade before the

welding procedure (see the following table).

The darkening shade may be manually adjusted

from 9 to 13 by twisting the darkening regula-

tor

on the outside of the helmet.

ATTENTION! The darkening regulator

has

the setting position “grind“. If the darkening

regulator

is set to this position the automatic

darkening is deactivated.

Only use this setting when you do not wish to

use the welding helmet for welding. The auto-

matic darkening is then no longer active.

Check the light density before each use.

Test procedure: Bring the viewing panel closer

to an external light source with a value of more

than 40 W and examine whether or not the

screen darkens or illuminates.

To change the UV ﬁlter / solar cells, push in both

tabs and pull the front frame outward. Fig. B

(Item no. 2000) or loosen the two screws as

shown in Fig. A (Item no. 2001, 2002).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 281392 PSH 3 A2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info