Bedienungsanleitung Parkside IAN 281406 PFBS 160 B2 (Seite 34 von 130) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746425

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

PFBS 160 B2

│

31 ■

■ Note that the maximum diameter of the grind-

ing assembly and of grinding cones, pencil

grinders and grinding points with a thread insert

may not exceed 55mm and the maximum

diameter for sandpaper sanding accessories

may not exceed 80mm.

NOTE

► The max. permissible length of a mandrel is

33 mm.

■ Store the accessories in the original box or store

the accessory components somewhere else to

protect them from damage.

■ Store the accessories somewhere dry and not in

the vicinity of aggressive media.

■ If you exert too much pressure, the ﬁtted tool

can break and/or the workpiece could be dam-

aged. You will achieve optimum working results

by moving the tool over the workpiece at a

steady speed and while exerting light pressure.

■ When carrying out cutting work, hold the appli-

ance ﬁrmly with both hands.

■ Observe the data and the information in the ta-

ble to prevent the end of the spindle from touch-

ing the perforated base of the grinding tool.

Flexible shaft

■ Never operate the spindle lock while the motor

is running. Otherwise, the appliance or the ﬂex-

ible shaft may be damaged.

♦ Screw the union nut anticlockwise oﬀ the

appliance and store it carefully.

♦ Press the spindle lock

and hold it down.

♦ Screw the tensioning nut

anticlockwise oﬀ

the appliance.

♦ Fit the ﬂexible shaft

onto the appliance. To

do this, the internal access of the ﬂexible shaft

push the tensioning nut into the collet chuck

, .

♦ First tighten the tensioning nut

and then the

union nut

14b

of the ﬂexible shaft clockwise

onto the appliance with the combination span-

ner .

♦ Place the desired accessory into the collet

chuck

, of the ﬂexible shaft.

♦ Push the black the collar back onto the ﬂexible

shaft to lock the spindle.

♦ Open the collet chuck mount

on the ﬂexible

shaft with the combination spanner . Fit the

attachment and screw the collet chuck mount

back in place.

Stand for the multi-tool

♦ Screw the stand into the clamping device .

NOTE

► Depending on the desired attachment onto a

vertical or horizontal surface, you can screw

the stand

into the clamping device in two

diﬀerent positions.

♦ Screw the clamping device

onto the edge of

a work bench or table with a maximum thick-

ness of 55 mm.

♦ The stand

is height-adjustable. Undo the

upper part of the stand by turning it anti-

clockwise (−). Pull out the tube to the maximum

height and lock it again by turning it clockwise

(+).

♦ The mount

is also height-adjustable; turn

the black thread anticlockwise. After you have

set the mount to the correct height, tighten the

thread by turning in the opposite direction.

♦ Fix the appliance with the metal clip

onto the

mount of the stand . The mount can be

turned 360°.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 281406 PFBS 160 B2 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info