748017
26
Zoom out
Zoom in
Vorherige Seite
1/83
Nächste Seite
26 GB/IE
If electrical contact voltage occurs,
immediately switch the equipment
off and have it inspected by an
electrically skilled person.
Always ensure good electrical
contacts on the welding current
end.
Always wear insulating gloves on
both hands whilst welding. These
will protect from electric shock
(no-load voltage of the welding
current), from hazardous rays
(heat and UV rays) and glowing
metal and weld splashes.
Wear solid, insulating shoes. The
shoes should also insulate when
exposed to moisture. Low shoes
are not suitable, as glowing metal
drops falling could cause burns.
Wear suitable protective clothing,
no synthetic garments.
Do not look into the arc with
unprotected eyes, only use a
welding shield with approved
protective glass per DIN. In
addition to light- and heat rays
which could result in blinding or
burns, the arc also emits UV rays.
Without adequate protection,
this invisible ultraviolet radiation
causes very painful conjunctivitis
which is only noticed a few hours
later. UV rays further cause burns
similar to a sunburn in unprotected
areas of the body.
Persons near the arc or assistants
must also be informed of the risks
and outfitted with the necessary
protection. If necessary, set up
protective panels.
Ensure an adequate supply of
fresh air whilst welding,
particu-
larly in small spaces, as it produces
smoke and harmful gasses.
Do not weld containers in which
gasses, fuels, mineral oils, etc.
were stored - even if emptied a
long time ago - as residue poses
an explosion hazard.
Special regulations apply in rooms
posing fire- and explosion hazards.
Welded joints exposed to great
strain and needing to meet cer-
tain safety requirements must be
made by specially trained and
certified welders. Examples are
pressure vessels, running rails,
tow couplings, etc.
ATTENTION! Always connect
the earth terminal as close as
possible to the point of weld to
provide the shortest possible path
for the welding current from the
electrode to the earth terminal.
Never connect the earth terminal
to the housing of the welding
equipment!
Safety instructions
281479_Inverter Schweissgeraet PISG 80 A1_content_OS.indd 26 28.12.16 12:19
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 286508 PISG 80 A2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info