748024
25
Zoom out
Zoom in
Vorherige Seite
1/102
Nächste Seite
GB IE
25
Direction switch may only be acti-
vated at a standstill to prevent dam-
age to the transmission.
Inserting/replacing bits
Prior to commencing any work
on the device, bring the direction
switch (
9) to the neutral position
in order to prevent an accidental
start up.
1. Insert the desired bit (14) or bit
holder (15) into the bit adapter
(11). It locks into place audibly.
2. To remove the bit or bit holder
pull the spring sleeve (1) back.
3. With the spring sleeve (1) pulled
back remove the bit or bit holder
from the bit adapter (11). Release
the spring sleeve.
Torque setting
Always turn off the device, before
setting the torque.
1. Turn the adjusting ring (2) to se-
lect the desired torque:
Step 1 --> lowest torque,
Step MAX --> highest torque

Screws: Steps 1 - 6
Drilling: Step MAX.
2. Start with a lower torque step
and increase according to re-
quirement.
The necessary torque is dependent
on:
- the type and hardness of the
material to be treated;
- the type and length of the
screws used.
Handle setting
Prior to commencing any work on the
device, bring the direction
switch (
9) to the neutral position in
order to prevent an accidental start up.
The device can be locked in two hand settings:
- Pistol grip position
- Rod position
Press the release key PRESS (4) and
turn the handle (6) of the device by
180°. It locks into place audibly.
Use as a torch
1. Press the torch lens (5) on the
underside of the handle (6). The
torch LEDs light up.
2. To switch off the LEDs press the
torch lens (5) again.
Cleaning/Maintenance
Leave any work not covered in this
manual to our Service Centre. Only use
original parts. There is a risk of injury!
Cleaning
Clean and service the device regularly as fol-
lows. This guarantees a long life for your unit:
Do not jet water onto the ap-
pliance and do not clean it un-

result in the danger of an elec-
tric shock and the appliance
could be damaged.

and handles on the equipment clean. To do
this, use a damp cloth or brush.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 290720 PSSA 3.6 D4 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info