Bedienungsanleitung Parkside IAN 292291 PBS 350 A1 (Seite 28 von 72) (Deutsch, Englisch, Holländisch, Französisch)

747882

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

GB/IE 21

Causes are:

• Drag marks if connection lines are led through window or

door clearances.

• Kinks due to improper attachment or routing of the con-

nection line.

• Cuts caused by running over the connection line.

• Insulation damages caused by pulling the connection line

out of the wall socket.

• Fissures caused by the ageing of the insulation.

Such defective electric connection lines must not be used and

are hazardous due to the insulation damages.

Regularly check the electrical connection lines for damages.

Please make sure that the connection lines are disconnected

from the mains supply during the check.

Electrical connection lines must comply with the relevant VDE

and DIN regulations. Only use connection lines labelled with

H05VV-F.

The labelling of the connection cable with the type speciﬁ-

cation is required.

AC motor

• The mains voltage must be 230 - 240 V~

• Extension cables up to 25 m long must have a cross-section

of 1.5 mm

Connections and repairs of electrical equipment may only be

carried out by an electrician.

Please provide the following information in the

event of any enquiries:

• Type of current for the motor

• Machine data - type plate

16. Disposal and recycling

The equipment is supplied in packaging to preven it from be-

ing damaged in transit. The raw materials in this packaging

can be reused or recycled.

The equipment and its accessories are made of various types

of material, such as metal and plastic. Defective components

must be disposed of as special waste. Ask your dealer or

your local council.

When producing angled cuts, only use the parallel stop to

the right of the saw band.

12.3 Freehand cuts (Fig. 19)

One of the most important features of a band saw is the ease

with which it can cut curves and radii.

• Lower the saw band guide (5) onto the workpiece (see

9.5).

• Switch on the saw.

• Press the workpiece ﬁrmly onto the saw bench (7) and

slowly slide into the Bandsaw blade (21).

• In many cases it is helpful to roughly saw curves and cor-

ners approximately 6 mm from the line.

• If it is necessary to saw curves that are too tight for the saw

band used, auxiliary cuts must be sawn up to the front face

of the curve, so that these fall oﬀ as wood waste when the

ﬁnal radius is sawn.

13. Cleaning and maintenance

Warning! Prior to any adjustment, maintenance or service

work disconnect the mains power plug!

Cleaning

Keep all safety devices, air vents and the motor housing free

of dirt and dust as far as possible. Wipe the equipment with

a clean cloth or blow it with compressed air at low pressure.

We recommend that you clean the device immediately each

time you have ﬁnished using it.

Maintenance

There are no parts inside the equipment which require ad-

ditional maintenance.

14. Storage

Store the device and its accessories in a dark, dry and frost-

proof place that is inaccessible to children. The optimum stor-

age temperature is between 5 and 30˚C.

Store the power tool in original packaging.

Cover the electrical tool in order to protect it from dust and

moisture.

Store the operating manual with the electrical tool.

15. Electrical Connection

The installed electric motor is connected and is ready to work.

The connection complies with the relevant VDE and DIN regu-

lations. The customer-side mains supply and the used exten-

sion line must meet these regulations.

Important information

In the event of an overloading the motor will switch itself

oﬀ. After a cool-down period (time varies) the motor can be

switched back on again.

Defective Electric Connection Lines

Often, insulation damages occur on electrical connection

lines.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 292291 PBS 350 A1 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info