Bedienungsanleitung Parkside IAN 292293 PDBG 125 A1 (Seite 22 von 97) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

747887

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

8. Never use damaged or incorrect

blade washers or bolts. The blade

washers and bolt were specially designed

for your saw, for optimum performance and

safety of operation.

Further safety instructions for all saws –

Kickback causes and related warnings

¢ A kickback is a sudden reaction to a pinched,

bound or misaligned saw blade, causing

an uncontrolled saw to lift up and out of the

workpiece toward the operator;

¢ when the blade is pinched or bound tightly

by the kerf closing down, the blade stalls and

the motor reaction drives the unit rapidly back

toward the operator;

¢ if the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the

wood causing the blade to climb out of the

kerf and jump back toward the operator.

Kickback is the result of saw misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

1. Maintain a ﬁrm grip with both hands

on the saw and position your arms

to resist kickback forces. Position

your body to either side of the blade,

but not in line with the blade. Kickback

could cause the saw to jump backwards,

but kickback forces can be controlled by the

operator, if proper precautions are taken.

2. When blade is binding, or when

interrupting a cut for any reason,

release the trigger and hold the

saw motionless in the material

until the blade comes to a complete

stop. Never attempt to remove

the saw from the work or pull the

saw backwards while the blade is

in motion or kickback may occur.

Investigate and take corrective actions to

eliminate the cause of blade binding.

3. When restarting a saw in the

workpiece, centre the saw blade in

the kerf and check that saw teeth

are not engaged into the material.

If saw blade is binding, it may walk up or

kickback from the workpiece as the saw is

restarted.

4. Support large panels to minimise the

risk of blade pinching and kickback.

Large panels tend to sag under their own

weight. Supports must be placed under the

panel on both sides, near the line of cut and

near the edge of the panel.

5. Do not use dull or damaged blades.

Unsharpened or improperly set blades

produce narrow kerf causing excessive

friction, blade binding and kickback.

6. Blade depth and bevel adjusting

locking levers must be tight and

secure before making cut. If blade

adjustment shifts while cutting, it may cause

binding and kickback.

7. Use extra caution when sawing into

existing walls or other blind areas.

The protruding blade may cut objects that can

cause kickback.

Safety instructions for circular saws with

inner pendulum guard - Lower guard

function

1. Check lower guard for proper

closing before each use. Do not

operate the saw if lower guard does

not move freely and close instantly.

Never clamp or tie the lower guard

into the open position. If saw is

accidentally dropped, lower guard may be

bent. Raise the lower guard with the retracting

handle and make sure it moves freely and

does not touch the blade or any other part, in

all angles and depths of cut.

2. Check the operation of the lower

guard spring. If the guard and the

spring are not operating properly,

they must be serviced before use.

Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a build-up

of debris.

3. Lower guard may be retracted

manually only for special cuts such

as “plunge cuts” and “compound

cuts”. Raise lower guard by retracting

handle and as soon as blade enters the

material, the lower guard must be released.

For all other sawing, the lower guard should

operate automatically.

4. Always observe that the lower

guard is covering the blade before

placing saw down on bench or ﬂoor.

An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in

its path. Be aware of the time it takes for the

blade to stop after switch is released.

24 GB / IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 292293 PDBG 125 A1 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info