Bedienungsanleitung Parkside IAN 292293 PDBG 125 A1 (Seite 25 von 97) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

747887

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Q Lubrication

This product features a lubrication system utilizing

wax sticks

to clean and lower friction between

the two blades rotating in counter-direction.

1. Insert a wax stick

into the wax stick

holder

(see ﬁg. E).

2. Turn the wax stick dial

clockwise until it

touches the blades.

3. Slightly turn the wax stick dial

counter-

clockwise to create a little clearance between

wax stick

and blades.

4. Occasionally turn the wax stick dial

slightly clockwise during operation to

lubricate the blades.

Q Attaching / removing a dust

extraction device

WARNING!

u During operation ﬁne dust will be generated!

Some dusts are highly inﬂammable and

explosive! Always attach a dust extraction

device when using this product in order to

keep the working area clean! Wear a dust

mask when operating this product! Dust can

be harmful to health! Especially dust and

chips of wood that has been treated, e.g.

with wood preservative or a stain!

u Do not smoke during operation, keep heat

sources and open ﬂames out of the working

area!

This product features a designated dust extraction

outlet

to connect a vacuum cleaner reducing

generated dust during operation on the workpiece

and airborne.

1. Slide the dust extraction adaptor

over the

dust extraction outlet

, make sure it sits

snug.

2. Rotate the dust extraction adaptor

to your

needs (see ﬁg. F).

3. Remove the dust extraction adaptor

after

work by simply pulling it oﬀ.

Q Operation

CAUTION! RISK OF INJURY!

u Keep your hands away from the tool when

the product is in operation.

Q Cutting guide

The cutting guide

can be adjusted for diﬀerent

working positions.

1. Use the provided multi-tool

to loosen the

cutting guide screw

(see ﬁg. G).

2. Turn the cutting guide

to your desired

position.

3. Use the provided multi-tool

to tighten the

cutting guide screw

Q Switching on and oﬀ

Switching on:

1. Push the lock-oﬀ button

and keep it pressed.

2. Press the on / oﬀ switch

. Release the lock-oﬀ

button

once the product is running.

Switching oﬀ:

1. Release the on / oﬀ switch

to switch the

product oﬀ.

Q Cutting

This product features two counter-rotating blades,

cancelling each other’s pull force out, which makes it

ideal to perform cross and pocket cuts safely.

Cross cut

NOTE

u Always perform a trial cut into scrap

material along a marked cutting line on the

workpiece. The cutting guide indicates where

the cut will be made.

1. Secure the workpiece with suitable means.

2. Hold the product ﬁrmly with both hands on the

rear handle

and front handle

3. Switch on the product (see “Switching on and

oﬀ”). Let the blades reach full speed.

4. Guide the product into the workpiece to make

the cut.

5. Switch oﬀ the product and let the blades come to

full stop.

6. Lift the product oﬀ the workpiece.

7. Fig. H: rip cutting of chipboard or plywood (left);

cross cutting of natural timber (right).

8. Fig. I: cross cutting of a copper pipe (left);

cross cutting of an aluminum bar (right).

27 GB / IE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 292293 PDBG 125 A1 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info