Bedienungsanleitung Parkside IAN 300290 PDT 40 E4 (Seite 22 von 82) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

748082

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Safety / Preparing the product for use / Inbetriebnahme

5 DE/AT/CH

Inhaltsverzeichnis

Legende der verwendeten Piktogramme .........................................................Seite 6

Einleitung ........................................................................................................................................Seite 6

Bestimmungsgemäße Verwendung ...................................................................................................Seite 6

Ausstattung ..........................................................................................................................................Seite 6

Lieferumfang .......................................................................................................................................Seite 6

Technische Daten ................................................................................................................................Seite 7

Sicherheit ........................................................................................................................................Seite 7

Allgemeine Sicherheitshinweise ........................................................................................................Seite 7

Vor der Inbetriebnahme ....................................................................................................Seite 8

Gerät aufstellen ..................................................................................................................................Seite 8

Inbetriebnahme ........................................................................................................................Seite 8

Heizstufen und Ventilator ein- / ausschalten .....................................................................................Seite 8

Temperatur einstellen..........................................................................................................................Seite 9

Gerät ausschalten ..............................................................................................................................Seite 9

Überhitzungsschutz ............................................................................................................................Seite 9

Fehlerbehebung ........................................................................................................................Seite 10

Wartung, Reinigung und Lagerung .........................................................................Seite 10

Service ...............................................................................................................................................Seite 10

Garantie ...........................................................................................................................................Seite 11

Entsorgung.....................................................................................................................................Seite 11

Original-EG-Konformitäts erklärung / Hersteller .........................................Seite 12

277044_par_ROWI_Heizgeblaese_content_AT.indd 5 13.07.16 08:49

GB/IE/NI 23

Proper functioning of the fastener driving tool re-

quires ﬁltered, dry and oiled compressed air in

adequate quantities. If the air pressure in the line

system exceeds the maximum permissible opera-

ting pressure of the fastener driving tool, a pressure

reducing valve followed by a downstream safety

valve shall additionally be ﬁtted in the supply line

to the tool.

Note: When compressed air is generated by com-

pressors, the natural moisture in the air condenses

and collects as condensed water in pressure ves-

sels and pipelines. This condensate must be remo-

ved by water separators. These water separators

must be checked on a daily basis and drained if

necessary, since corrosion can otherwise develop

in the compressed air system and in the fastener

driving tool, which serves to accelerate wear.

The compressor plant shall be adequately dimensi-

oned in terms of pressure output and performance

(volumetric ﬂow) for the consumption which is to

be expected. Line sections which are too small in

relation to the length of the line (pipes and hoses),

as well as overloading the compressor, will result

in pressure drops.

Oilers should be checked daily and, if necessary,

ﬁlled with the recommended oil (see technical

data). When using hose lengths over 10m, the sup-

ply of the nailer with oil is not guaranteed. We th-

erefore recommend an lubricator attached directly

to the fastener driving tool or to manually lubricate

the air inlet directly with 2 - 5 drops of the recom-

mended grade of oil(see technical data).

Use only hoses with an internal diameter not less

than 9mm. Otherwise the staples/nails will be shot

out of the machine slow and with little pressure.



Loading the magazine

Only those fasteners speciﬁed under technical data

may be used. When ﬁlling the magazine, hold the

tool so that the muzzle is not pointing towards your

own body or towards any other person.

1. Press the magazine lever

and pull the maga-

zine cover back to its stop position.

2. Insert the corresponding fastener (nails, see

Fig. B or staples, see Fig. C) into the magazi-

. The tacks must be put on the rail of the

magazine

3. Slide the magazine cover forwards until it locks.



 Use

□

Load the magazine

of the compressed air

tacker as described in the chapter “Loading

the magazine“.

□

Use the pressure reducer to set the correct ope-

rating pressure.

□

Ensure that the permissible operating pressu-

re of 8 bar at the device is never exceeded.

Operating pressure that is too high does not

provide any performance increase, but only

increases compressed air consumption and ac-

celerates wear on the device.

□

Switch on the compressor.

□

Allow the compressor to run once long enough

until maximum tank pressure is reached and

the device is switched off.

□

Place the compressed air tacker on the work-

piece and press the trigger

NOTE: The compressed air tacker is

equipped with a trigger lock

. The fas-

tener will only leave the device when the

mouth of the compressed air tacker is

pressed against the workpiece and the

trigger

is actuated.

Handling the tool

Note the section with special safety references of

these operating instructions. Having checked that

the fastener driving tool is functioning correctly,

apply the tool to a workpiece and actuate the trigger.

□

Check that the fastener has been driven in cor-

responding to the work requirements.

– If the fastener is protruding, increase the air

pressure in 0.5 bar increments.

– If the fastener is too deep, decrease the air

pressure in 0.5 bar increments.

Operation / Use

Parkside IAN 300290 PDT 40 E4 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info