748958
25
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
25
GB IE
32 Interlock switch
33 Lever for V-belt tension
F
34 On/Off switch, laser
35 Controller, laser
G
36 Battery compartment, laser
H
37 Middle drive pulley
38 Intake, middle drive pulley
39 Bearing points, intake
40 Bearing points, intake
I
41 Mounting screw, laser
Technical Data
Bench Pillar Drill ........PTBM 500 E5
Rated input voltage ..........230 V~, 50 Hz
Power input ............ 500 W (S2 15 min)*
Idling speed (n0)
Spindle ...................... 500 - 2500 min-1
Motor ................................ 1400 min-1
Safety class .......................................... I
Protection category...........................IPX0
Weight ........................................ 17 kg
Drill chuck ...........B16 (1.5 mm to 16 mm)
Spindle stroke .............................. 50 mm
Workpiece size ....................max. 60 mm
Laser class ...........................................2
Laser wavelength ........................650 nm
Laser power ..............................< 1 mW
Power supply
Laser module ........ 2 x 1,5 V Micro (AAA)
Sound pressure level
(LpA) ...................... 71 dB(A); KpA= 3 dB
Sound power level (LWA)
measured ............. 84 dB(A); KWA= 3 dB
Vibration(ah) ..... < 2,5 m/s2; K= 1,5 m/s2
* After continuous operation of 15 minutes the
drill stops until the device temperature devi-
ates by less than 2 K (2°C) from the room
temperature.
Levels of noise and vibration were determi-
ned according to the norms and regulati-
ons in the declaration of conformity.
The vibration emission value has been
measured according to a standardised
testing method and may be used for com-
parison with another electric tool.
The indicated vibration emission value may
also be used for an introductory assess-
ment of the exposure.
Warning:
The vibration emission value whilst
actually using the electrical tool
may vary from the given values in-
dependently of the type and way in
which the electric tool is used.
Try to keep the exposure to vib-
rations as low as possible. An
example of a measure to reduce
vibration exposure is limiting the
working hours. For this purpose all
parts of the operating cycle have to
be considered (for example, times
when the electric tool is switched
off and times when it is switched on
but running without any load).
Notes on safety
Caution! When using power tools,
observe the following basic safety
measures for the prevention of
electric shocks and the risk of injury

Please read all these instructions
before using this electric tool and
please keep the safety instructions.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 304520 PTBM 500 E5 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info