Bedienungsanleitung Parkside IAN 310918 PHP 500 E3 (Seite 12 von 46) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

749301

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

PHP 500 E3 GB│IE │ 9 ■

the appliance. Cleaning and user

maintenance tasks may not be car-

ried out by children unless they are

supervised.

■ To avoid potential risks, damaged mains cables

should be replaced by the manufacturer, their

customer service department or a similarly

qualiﬁed person.

Additional safety instructions for

glue guns

■ Children should be supervised to ensure that

they do not play with the appliance.

■ CAUTION! This appliance must be placed on

its stand when not in use.

■ Always protect the appliance from rain and

moisture. Water entering a power tool will

increase the risk of electric shock.

■ Do not misuse the power cord, e.g. to carry

or hang up the appliance, or to pull the plug

from the socket. Keep cord away from heat,

oil, sharp edges or moving parts. If the power

cord is damaged or severed during work, do

not touch the cord but rather pull out the power

plug. Damaged or entangled cords increase the

risk of electric shock.

■ Only for indoor use.

■ If you take a break of longer than 30 minutes,

pull out the power plug.

■ Allow the appliance to cool completely after

use and before storage.

■ Do not work on any material containing asbestos.

■

200

Avoid the risk of injury or ﬁre as well as

health risks: RISK OF BURNS! The

adhesive and the nozzle reach a

temperature of around 200°C. Do not touch the

nozzle or the glue. Do not allow hot glue to come

into contact with people or animals. In case of

contact with skin, rinse the aﬀected part in cold

running water for a few minutes. Do not attempt to

remove the adhesive from the skin.

■ Always route the power cable towards the rear,

away from the appliance.

■ Do not pull back the glue stick!

Cut it oﬀ to store the device in the

carrying case.

Operation

Before use

Preparing the surfaces to be glued:

■ Do not use ﬂammable solvents to clean the

surfaces to be glued.

■ The ambient temperature and the materials to

be bonded may not be colder than 5°C and

not warmer than 50°C.

■ The area to be glued must be clean, dry and

free of grease.

♦ Smooth surfaces should be roughened before

gluing.

♦ Quick-cooling materials such as steel should be

warmed a little to facilitate adhesion.

Using the appliance

Mains operation:

♦ Connect the power cable to the mains

connection of the glue gun (see ﬁg. A).

Insert the power plug into the socket.

♦ Fold down the plastic stand . Put down the

appliance.

♦ Push a glue stick into the feeder shaft .

♦ Allow the appliance to heat up for about

5 minutes. The appliance is now ready for use.

Battery operation:

♦ Connect the power cable to the mains

connection of the charger . Insert the power

plug into the socket.

♦ Place the glue gun into the charger .

♦ Push a glue stick into the feeder shaft .

♦ Allow the appliance to heat up for about

5 minutes. The appliance is now ready for use.

♦ Repeat the heating phase if the glue is still too

thick or viscous.

Gluing:

♦ Pull the trigger to control the ﬂow of glue in

accordance with your requirements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 310918 PHP 500 E3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info