Bedienungsanleitung Parkside IAN 311854 PATC 2 A1 CORDLESS (Seite 16 von 53) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

749288

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

16 GB/IE

Before use

Charging the product

Note: Remove all packaging materials from the product.

Note: You can recharge the product using a normal household socke

or using your car‘s cigarette lighter socket.

Note: The fuse of the car adapter 12 can be exchanged. The tech-

nical data of the fuse must comply with information given in the sec-

tion “Technical data”. The fuse may only be replaced by a qualiﬁed

electrician.

CAUTION! Do not connect the product to your car‘s cigarette

lighter socket if the car battery is already old and worn. Doing so

could mean that the car engine will no longer start.

Note: In order to use the product without a mains adapter 11 or a

car adaptor 12 , you need to recharge the rechargeable battery

before use. The charging process takes about 5–7 hours.

Note: Charge the product for approx. 12 hours prior to ﬁrst use.

Connect the USB cable 13 with the USB connector of the mains

adapter 11 or the car adapter 12 .

Connect the micro-USB connector on the USB cable 13 to the

micro-USB input socket 8 on the product.

Plug the mains adapter 11 into a socket, or plug the car adapter

12 into the cigarette lighter socket in your vehicle.

Note: During charging from a cigarette lighter socket, ensure that

the car adapter 12 is always completely inserted into the cigarette

lighter socket of the vehicle. Failure to observe this advice may result

in risk of ﬁre from overheating

Note: During charging, the charging indicator 9 lights up red.

When charging is complete, the charging indicator 9 lights up

green. When the charging indicator 9 is green, pull the mains

adapter 11 out of the socket or the car adapter 12 out of the

cigarette lighter socket. Disconnect the adapter from the product to

prevent the rechargeable battery from discharging.

Use

You can secure the product by using the folding hook 10 or the

magnetic base 4 on a ﬂat, ferromagnetic surface.

Using the product without

a power connection

Fully charge the product as described in the section

“Charging the product“.

Press the ON / OFF switch 2 once to switch on the hand

spotlight 1 with full power.

Press the ON / OFF switch 2 again to switch on the hand

spotlight 1 with low power.

Press the ON / OFF switch 2 again to switch oﬀ the hand spot-

light 1 and switch on the orientation light 6.

Press the ON / OFF switch 2 again to switch oﬀ the orientation

light 6.

To switch on the telescopic work light 3, pull the hand spotlight

1 carefully out of the lamp body, with holding the grip 7.

To switch the telescopic work light 3 oﬀ, push the hand spot-

light 1 back into the lamp body, with holding the grip 7 (see

Fig. A).

The lamp head may be titled over 90º to allow for lighting a

speciﬁc work area (see Fig. A).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 311854 PATC 2 A1 CORDLESS Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info