Bedienungsanleitung Parkside IAN 38175 PWS 1010 (Seite 57 von 77) (Englisch, Italienisch, Portugiesisch, Spanisch)

744800

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

56 GB/MT

General safety advice for electrical power tools

d) Do not switch on the device if the cut-

ting disc is in the workpiece. Allow the

cutting disc to reach full speed before carefully

continuing with the cut. Otherwise the disc

could snag, jump out of the workpiece or

cause a kickback.

e) Support boards or workpieces whilst

cutting to reduce the risk of kickback

caused by a jammed cutting disc. Large

workpieces may bend under their own weight.

The workpiece must be supported to both sides

of the cutting disc and particularly near the

cutting disc and at the workpiece edge.

f) Be particularly careful when pocket

cutting in existing walls or other areas

where you cannot see what you are

cutting into. The cutting disc plunged into

the surface could cut through gas or water

pipes, electricity cables or other objects and

cause kickback.



Special safety advice for

abrading using sandpaper

 Do not use over-sized sanding sheets.

Follow the manufacturer’s recommen-

dations for sanding sheet size. Sanding

sheets that project beyond the backing pad

could cause injury in addition to jamming, tear-

ing of the sheet or kickback.



Special safety

advice for polishing

 Do not use the polishing bonnet if it

has any loose parts, in particular the

fastening cords. Tuck the fastening cords

away or trim them. Loose fastening cords rotat-

ing with the attachment could catch your ﬁngers

or become trapped in the workpiece.



Special safety advice for

working with wire brushes

a) Bear in mind that wire brushes lose

pieces of wire during normal use. Do

not overload the wires by applying too

much pressure. Flying pieces of wire can very

easily penetrate thin clothing and / or skin.

b) Use a guard, if recommended, but

make sure that the wire brush does

not come into contact with the guard.

The diameters of disc brushes and cup brushes

can increase due to contact pressure and cen-

tripetal forces.

Safety advice for

angle grinders

 Do not operate the device if the mains

lead or mains plug is damaged.

 Do not touch the mains lead if it be-

comes damaged or cut through while

you are using the device. Pull the plug

out of the mains socket immediately and have

the device repaired by a suitably qualiﬁed

person or at your service centre.

 Do not operate the device if it is damp

and do not use it in a damp environ

ment.

 If you use the device outdoors, always

connect it through a residual current

device (RCD) with a maximum trip cur-

rent of 30 mA. If using an extension lead,

always use one that is approved for outdoor use.

 Do not suspend or carry the device by

the mains lead. Always work with the

mains lead leading away from the

rear of the device.

 Grinding discs must be carefully kept

and handled in accordance with the

manufacturer’s instructions.

 Make sure that abrasive consumables

and tools are attached in accordance

with the manufacturer’s instructions

and advice.

 Ensure that any spacers supplied and

required for the use of certain abrasive

consumables and tools are installed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 38175 PWS 1010 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 38175 PWS 1010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info