Bedienungsanleitung Parkside IAN 46883 PBH 1050 A1 (Seite 27 von 33) (Französisch)

745200

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

27 GB

Introduction Introduction / General safety advice on power tools

Main handle

Hammer drilling in

Concrete: a

h(HD)

= 9.853 m / s

K = 1.5 m / s

Additional handle

Hammer drilling in

Concrete: a

h(HD)

= 8.967 m / s

, K = 1.5 m / s

Main handle

Chiselling: a

h(CHeq)

= 12.738 m / s

K = 1.5 m / s

Additional handle

Chiselling: a

h(CHeq)

= 8.278 m / s

K = 1.5 m / s

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibrati

on level may change with the application

of the tool and in some cases may be higher than

the value speciﬁed in these instructions. Regularly

using the electric tool in such a way may make it

easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particu-

lar period of work, you should also take into account

the intervening periods of time when the device is

switched oﬀ or is running but is not actually in use.

This can clearly reduce the vibration load through-

out the work period.

General safety advice on

power tools

Please read all safety in-

formation and instructions. Failure to observe

the safety information and instructions can result in

electric shock, ﬁre and / or serious injury.

Keep all safety advice and instructions in

a safe place for future reference.

The term “power tool” as used in the safety advice

refers to electrical tools powered by mains electric-

ity (with mains lead) and electrical tools powered

by rechargeable batteries (without mains lead).

1. Workplace safety

a) Keep your work area clean and well lit.

Untidy or poorly lit work areas can lead to ac-

cidents.

b) Do not use the power tool in potential-

ly explosive environments containing

ﬂammable liquids, gases or dusts. Pow-

er tools create sparks which can ignite dusts or

fumes.

c) Keep children and other people away

whilst operating the electrical tool.

Distractions can cause you to lose control of

the device.

2. Electrical safety

a) The mains plug on the device must ﬁt

the mains socket. The plug must not

be modiﬁed in any way. Never use

adapter plug on earthed power tools.

Unmodiﬁed plugs and the correct sockets reduce

the risk of electric shock.

b) Avoid touching grounded surfaces such

as pipes, radiators, ovens, and refrig-

erators. There is a higher risk of electric shock

if your body is earthed.

c) Keep the device away from rain or

moisture. Water penetrating the electrical

device increases the risk of an electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended,

e.g. to carry the device, to hang up

the device or to pull the mains plug

out of the mains socket. Keep the mains

lead away from heat, oil, sharp edges

or moving equipment parts. Damaged

or tangled cables increase the risk of an elec-

tric shock.

e) When using power tools outdoors al-

ways use extension cords approved

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 46883 PBH 1050 A1 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 46883 PBH 1050 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info