Bedienungsanleitung Parkside IAN 55730 PSE 2800 A1 (Seite 29 von 34) (Deutsch, Englisch, Holländisch)

745204

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

29 GB

Safety instructions / Before use … / … / Cleaning, maintenance, storage, transport and ordering replacement parts

connector

of the generator (ﬁg. C / Pos. 4)

and from the other side to an external ground.

Operation

ATTENTION! When being used for the ﬁrst

time, motor oil (15 W-40, approx. 0.6 l) and petrol

(unleaded normal petrol) must be put in.

Check the fuel level and the oil, and if necessary

top them up.

Make sure you have adequate ventilation.

Ensure that the spark cable is securely in the

spark plug.

Unplug any electric device connected to the

generator.

Start the engine

ATTENTION! When starting with the express

start

you can injure your hand with the sudden

kick back.

Wear protective gloves when starting.

Open the petrol tap

by turning the tap down-

wards.

Put the on / oﬀ switch

to the on position.

Turn the choke lever

to I Ø I (in the left

position).

Start the engine with the express start

sharply pulling the handle. If the engine has not

started pull the handle again.

Push the choke lever

back once the engine

has started (in the right position).

To load the generator

Connect the device to the 230 V∼ socket

ATTENTION! This socket can be loaded con-

tinuously (S1) with 2600 W and short term (S2) for

a maximum of 2 minutes with 2800 W.

Note: Some electric devices (sabre saws, drills etc.)

can use more electricity when doing heavy duty tasks.

Storing the engine

Before putting away, let the generator run with-

out load so that the device can „cool down“.

Turn the on / oﬀ switch

to the „OFF“ position.

Close the petrol tap

Overload protection

2 x 230 V sockets

WARNING! This generator is fitted

with an overload protector.

This cuts oﬀ the sockets

. By activating the over-

load switch

the sockets

can be used again.

ATTENTION! If this happens reduce the

amount of electrical output which you are

extracting from the generator or remove

defective devices which are attached.

ATTENTION! Faulty overload switches

should only be replaced with identically

constructed overload switches with the

same performance data. Please use our

customer service department.

Cleaning, maintenance,

storage, transport and

ordering replacement parts

Before cleaning and maintenance work, turn oﬀ the

engine and pull the spark plug connector

out of

the spark plug

ATTENTION! Turn the device off imme-

diately and contact your Service Station:

- With unusual vibrations or noises.

- If the engine seems overloaded or has backﬁred.

Cleaning

Keep the safeguards, air vents (ﬁg. B / Pos. B1)

and the engine housing as dust and dirt free as

possible. Wipe the device with a clean cloth or

blow it with compressed air with low pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 55730 PSE 2800 A1 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 55730 PSE 2800 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info